VocoPro CDG-X3P - Manual (Page 9)

8
Getting connected cont.
Connecting the CDG-X3P to a Microphone
IMPORTANT! Before connecting a microphone, be sure the power is off or the volume is turned all the way down. When
the microphone is plugged in and the unit is on do not point the microphone toward the speakers or leave an unattended
microphone too close to the speakers when the volume is up. This can create a loud squeal called “feedback” and could
possibly damage your speakers.
1. Using a microphone cable, designed for use with most Karaoke products, connect a microphone to the end of the
cable with the “XLR” connector.
2. Connect the end of the cable with the ¼” connector into either of the MIC ¼” jacks on the front of the CDG-X3P.
The CDG-X3P is designed so you can connect other components to it and use the Karaoke features that are built-in to
the CDG-X3P in conjunction with those components.
Expanding Your System - Using the CDG-X3P with other components
You may use the Karaoke features that are built into the CDG-X3P with other components just by connecting the compo-
nents as described in this section. The Karaoke features will automatically be functional when additonal components are
properly connected.
Connecting a DVD Player or Mini-Disc Player to the CDG-X3P
Using and RCA connector cable, connect the “L” and “R” “DVD” INPUT jacks to the “L” and “R” “AUDIO OUTPUT” jacks
on the DVD player (check manufacturer’s instructions). Be sure to set the input selector on the front of the CDG-X3P to
“DVD”, otherwise there will be no sound. Play the DVD player as usual. Music from the DVD player will be audible from
your speakers and the Karaoke features will be functional.
Connecting a Laser Disc Player
Using and RCA connector cable, connect the “L” and “R” “LD” INPUT jacks to the “L” and “R” “AUDIO OUTPUT” jacks
on the LD player (check manufacturer’s instructions). Be sure to set the input selector on the front of the CDG-X3P to
“LD”, otherwise there will be no sound. Play the LD player as usual. Music from the LD player will be audible from your
speakers and the Karaoke features will be functional.
Connecting an Amplifier (for sound)
An amplifier should be connected to the CDG-X3P through the “L” and “R” “PRE” OUTPUT jacks located in the back of the
CDG-X3P (See manufacturer’s instructions with your amplifier)
Connecting an Additional Tape Deck to Play or Record On the CDG-X3P
To Play Music From an Additional Tape Deck Through the CDG-X3P: Using an RCA connector cable, connect the “L” and
“R” “AUX” INPUT jacks on the CDG-X3P to the “L” and “R” “AUDIO OUTPUT OR PLAY OUT” jacks on the tape deck (check
manufacturer’s instructions). Be sure to set the input selector on the front of the CDG-X3P to “AUX”, otherwise there
will be no sound. Play the tape deck as usual. Music from the tape deck will be audible from your speakers. All the Kara-
oke features will be functional except video.
To Record to the CDG-X3P from an Additional Tape Deck: To record music from the additional tape deck to the CDG-X3P
tape deck, play the additional tape deck and follow the directions for recording on the CDG-X3P tape deck under “USING
THE CASSETTE DECK, To Record
With The Cassette Deck”.
Connecting the CDG-X3P to Your Home Stereo
Using and RCA connector cable, connect the “L” and “R” “PRE” OUTPUT jacks on the CDG-X3P to any of the “L” and “R”
“AUDIO INPUT” channels i.e., “CD” or “AUX” on your stereo. DO NOT CONNECT TO THE PHONO JACKS. (Check manufac-
turer’s instructions). Be sure To set the input selector on your stereo to the corresponding input jacks you have selected
to connect the CDG-X3P, otherwise there will be no sound. Play the CDG-X3P as usual. Music from the CDG-X3P will be
audible from the stereo speakers. All the Karaoke features will be functional.