Document Outline

• Omni.Net Lite
• Copyright
• Federal Communications Commission (FCC) Interference Statement
• Safety Warnings
• ZyXEL Limited Warranty
• Customer Support
• Table of Contents
• List of Figures
• List of Tables
• Preface
• 1. Introduction
  • 1.1 About your TA
    • 1.1.1 TA Features
      • 1.1.1.1 ISDN Basic Rate Interface (BRI) Support
      • 1.1.1.2 Extensive Analog Phone Support
      • 1.1.1.3 Outgoing Data Call Bumping Support
      • 1.1.1.4 PPP Multilink
      • 1.1.1.5 Bandwidth-On-Demand
      • 1.1.1.6 PAP and CHAP Security
      • 1.1.1.7 Upgrade Firmware
      • 1.1.1.8 Supplementary Voice Features
      • 1.1.1.9 Switch Type
    • 1.1.2 TA and ISDN Interfaces
  • 1.2 TA Hardware and Driver Installation
  • 1.3 Top Panel LEDs
  • 1.4 Configuration Methods
• 2. Using the Utility
  • 2.1 Accessing the TA with the Utility
  • 2.2 Navigating the Utility
  • 2.3 System
  • 2.4 RS-232 Port: Local DN (Directory Number) and Call Type
    • 2.4.1 Introduction to PPP
    • 2.4.2 Multilink PPP (MP or MLP)
    • 2.4.3 BACP and BAP
    • 2.4.4 ISDN Protocols
    • 2.4.5 Configuring Local DN and Call Type
  • 2.5 RS-232 Port: PPP/MP Parameters
    • 2.5.1 Link Authentication
      • 2.5.1.1 Windows Authentication
    • 2.5.2 Call Bumping (Bandwidth Release) for Voice Calls
    • 2.5.3 Bandwidth On Demand (BOD)
    • 2.5.4 Configuring PPP/MP Parameters
  • 2.6 RS-232 Port: V.24 Signal
    • 2.6.1 RS-232 Flow Control
    • 2.6.2 Configuring V.24 Signal
  • 2.7 Incoming Call Screening
  • 2.8 Outgoing Call Screening
  • 2.9 Pre-stored Numbers
  • 2.10 RS-232 Port: Advance Setting
  • 2.11 Analog Port: Local DN and Options
    • 2.11.1 MSN (Multiple Subscriber Number) and Subaddress
      • 2.11.1.1 Phone Number Assignment Example
    • 2.11.2 Caller ID
      • 2.11.2.1 Type 1: On-hook Caller ID Transmission
      • 2.11.2.2 Type 2: Off-hook Caller ID Transmission
    • 2.11.3 Dialing Method
    • 2.11.4 Configuring Local DN and Options
  • 2.12 Voice Calls
    • 2.12.1 Placing a Voice Call
    • 2.12.2 Answering a Voice Call
    • 2.12.3 Intercom
    • 2.12.4 Supplementary Services
      • 2.12.4.1 The Flash Key
      • 2.12.4.2 Call Hold
      • 2.12.4.3 Call Waiting
      • 2.12.4.4 Call Transfer
      • 2.12.4.5 Three-Way Conference
• 3. Using AT Commands
  • 3.1 AT Commands Overview
  • 3.2 Accessing the TA Example
  • 3.3 AT Commands
    • 3.3.1 Data Command Sets
    • 3.3.2 Command Sets for Analog Ports
    • 3.3.3 Debug Command Sets
  • 3.4 Configuring Examples with AT Commands
    • 3.4.1 Phone Number Assignment
    • 3.4.2 Storing Phone Number
    • 3.4.3 Setting Ports Priority
    • 3.4.4 Disabling Call Waiting
    • 3.4.5 Link Authentication
    • 3.4.6 Call Bumping (Bandwidth Release) for Voice Calls
    • 3.4.7 Bandwidth On Demand (BOD)
    • 3.4.8 Incoming Call Screening
      • 3.4.8.1 Data Call
      • 3.4.8.2 Voice Call
    • 3.4.9 Outgoing Call Screening
      • 3.4.9.1 Data Call
      • 3.4.9.2 Voice Call
    • 3.4.10 Caller ID
  • 3.5 Result Codes
• 4. Using Tone Commands
  • 4.1 How to Use Tone Commands with a Telephone Keypad
    • 4.1.1 Tone and Ring Patterns
  • 4.2 Tone Commands
  • 4.3 Configuring Example with Tone Commands
    • 4.3.1 Phone Number Assignment
    • 4.3.2 Storing Phone Number
    • 4.3.3 Setting Ports Priority
    • 4.3.4 Disabling Call Waiting
    • 4.3.5 Incoming Call Screening
      • 4.3.5.1 Voice Call
    • 4.3.6 Outgoing Call Screening
      • 4.3.6.1 Voice Call
    • 4.3.7 Caller ID
• 5. Firmware Upgrade
  • 5.1 Upgrading Using the Utility
  • 5.2 Upgrading Using HyperTerminal Example
• 6. Troubleshooting
• Index
  • Numerics
  • A
  • B
  • C
  • D
  • E
  • F
  • G
  • H
  • I
  • L
  • M
  • N
  • O
  • P
  • Q
  • R
  • S
  • T
  • U
  • V
  • W
  • X
  • Z