Bosch GPO 14 CE Professional - Manual (Page 15)

16 | English
1 619 929 J63 | (9.9.11) Bosch Power Tools
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
08.09.2011
Assembly
Mounting the Protective Devices
f Before any work on the machine itself, pull the mains
plug.
f Operate your machine only with the auxiliary handle 7
or bow handle 2.
Auxiliary Handle
Screw the auxiliary handle 7 on the right or left of the machine
head depending on the working method.
Bow Handle
Fasten the bow handle 2 to the gear case as shown in the fig-
ure.
Mounting the Grinding Tools
f Before any work on the machine itself, pull the mains
plug.
Clean the grinder spindle 6 and all parts to be mounted.
For clamping and loosening the grinding tools, lock the grind-
er spindle with the spindle lock button 3.
f
Actuate the spindle lock button only when the grinder
spindle is at a standstill. Otherwise, the machine may be-
come damaged.
See graphics page for the mounting sequence.
Buffing Disc
Screw the clamping mandrel 8 firmly onto grinder spindle 6
and tighten it via the spanner surfaces with an open-end span-
ner.
Mount the clamping flange 9 and the buffing disc 10 onto the
clamping mandrel 8. Screw on the clamping nut 11 and tight-
en with the two-pin spanner.
Polishing Plate
Mount the two spacer discs 12 and the polishing plate 13 on-
to the spindle 6.
Screw on the round nut 14 and tighten with the two-pin span-
ner.
Pull the lamb’s wool bonnet 15 over the polishing plate 13
and tighten the attachment strings.
Polishing Sponge
Screw the polishing sponge 16 firmly onto the grinder spindle
6. The lambskin polishing bonnet 17 can be pulled over the
polishing sponge 16.
Rubber Sanding Plate
Place the rubber sanding plate 18 onto the grinder spindle 6.
Screw on the round nut 14 and tighten with the two-pin span-
ner.
Firmly press the sanding sheet 19 onto the bottom side of the
rubber sanding plate 18.
Felt Polishing Disc
Firmly screw the felt polishing disc 20 onto the grinder spin-
dle 6.
Cup Brush/Disc Brush
The cup brush/disc brush must be able to be screwed onto
the grinder spindle until it rests firmly against the grinder
spindle flange at the end of the grinder spindle threads. Tight-
en the cup brush/disc brush with an open-end spanner.
Approved Grinding Tools
All grinding tools mentioned in these operating instructions
can be used.
The permissible speed [min
-1 ] or the circumferential speed
[m/s] of the grinding tools used must at least match the values
given in the table.
Therefore, observe the permissible rotational/circumferen-
tial speed on the label of the grinding tool.
Dust/Chip Extraction
f Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Engineering Director
PT/ESI
max.
[mm] [mm]
D b d [min -1 ] [m/s]
180 – – 3000 80
100 30 M 14 3000 45
D
D
b
d
OBJ_BUCH-1284-002.book Page 16 Friday, September 9, 2011 8:58 AM