Grain Systems PNEG-573 - Manual (Page 24)

24
PRE START CHECKS FOR ALL PORTABLE DRYERS PRE START CHECKS FOR ALL PORTABLE DRYERS PRE START CHECKS FOR ALL PORTABLE DRYERS PRE START CHECKS FOR ALL PORTABLE DRYERS PRE START CHECKS FOR ALL PORTABLE DRYERS
PRE SEASON INSPECTION PRE SEASON INSPECTION PRE SEASON INSPECTION PRE SEASON INSPECTION PRE SEASON INSPECTION
Before the dryer is filled, thoroughly
inspect the unit and check the op-
eration of the dryer as follows.
11111
22222
33333
44444
SET CONTROL SWITCHES SET CONTROL SWITCHES SET CONTROL SWITCHES SET CONTROL SWITCHES SET CONTROL SWITCHES
Moisture Control Switch-ON
Moisture Control Thermostat-MINI-
MUM TEMPERATURE
Adjustable Grain Hi-Limit-MAXI-
MUM TEMPERATURE*
Load Switch-OFF
Unload Switch-OFF
Fan Switches-OFF
Burner Switches-OFF
Out of Grain Timer-1 MINUTE
Load Delay-30 SECONDS
Unload Delay-30 SECONDS
Metering Roll Speed-LOW AND
HIGH SPEED--000
Dry Timer-1 MINUTE
Cool timer-1 MINUTE
Unload timer-30 SECONDS
Mode Switch-CONTINUOUS FLOW
*On multi-fan models
Open all metering roll access metering roll access metering roll access metering roll access metering roll access
doors doors doors doors doors and inspect each compart-
ment for any bolts, nuts or other for-
eign material, that may cause pos-
sible jamming of the metering rolls
metering rolls metering rolls metering rolls metering rolls.
INSPECT THE METERING INSPECT THE METERING INSPECT THE METERING INSPECT THE METERING INSPECT THE METERING
ROLLS ROLLS ROLLS ROLLS ROLLS
BEFORE ATTEMPTING TO
OPERATE THE DRYER MAKE
SURE ALL SAFETY SHIELDS
ARE IN PLACE, ALL BOTTOM
CLEANOUT AND REAR
ACCESS DOORS ARE CLOSED
AND ALL PERSONNEL ARE
CLEAR OF THE DRYER
Turn the CONTROL POWER switch
to ON. The switch will light up. A
copyright message, model number,
total running time in hours and min-
utes, current date and time will ap-
pear. At this point the controller will
lock out all other dryer functions.
Push the DRYER START button,
and all the selector switches on the
control panel will be activated.
POWER START BUTTON POWER START BUTTON POWER START BUTTON POWER START BUTTON POWER START BUTTON
Once the date and time appear,
press RESET and the dryer will per-
form its safety circuit check. If a fault
is found, the cause will be displayed
on the LCD. If all are found safe,
the controller will supply power to the
electronic fuel shut-off valve
electronic fuel shut-off valve electronic fuel shut-off valve electronic fuel shut-off valve electronic fuel shut-off valve, if so
equipped, and the DRYING MODE
switch will light up, indicating that the
dryer is ready to be started.
Turn ON the electrical power sup- electrical power sup- electrical power sup- electrical power sup- electrical power sup-
ply ply ply ply ply to the dryer; set all circuit break- circuit break- circuit break- circuit break- circuit break-
ers ers ers ers ers to ON, including the safety dis- safety dis- safety dis- safety dis- safety dis-
connect handle connect handle connect handle connect handle connect handle mounted on the
front of the dryer power panel
dryer power panel dryer power panel dryer power panel dryer power panel.
ELECTRICAL POWER ELECTRICAL POWER ELECTRICAL POWER ELECTRICAL POWER ELECTRICAL POWER
CONTROL POWER SWITCH CONTROL POWER SWITCH CONTROL POWER SWITCH CONTROL POWER SWITCH CONTROL POWER SWITCH
The metering roll access area: 1-Metering roll, 2-Strike-off plate, 3-Adjust- The metering roll access area: 1-Metering roll, 2-Strike-off plate, 3-Adjust- The metering roll access area: 1-Metering roll, 2-Strike-off plate, 3-Adjust- The metering roll access area: 1-Metering roll, 2-Strike-off plate, 3-Adjust- The metering roll access area: 1-Metering roll, 2-Strike-off plate, 3-Adjust-
ing bolt, 4-Unload auger. ing bolt, 4-Unload auger. ing bolt, 4-Unload auger. ing bolt, 4-Unload auger. ing bolt, 4-Unload auger.