Document Outline

• Cover of Manual
• Specifications
  • Output
  • Input
  • Connections
  • Environmental
  • Miscellaneous
  • Safety
  • Other Referenced Standards
• Important Safety Instructions
• Body of Manual
  • Introduction
    • Scope of the Manual
    • Product Overview
    • System Configurations
    • Part Numbers and List Options
  • Features
    • System Overview
    • Tiered Distribution Features
      • Overview (Vista II Two-Tier)
      • DC Distribution Installed
        • Tier 1 (Lower)
        • Tier 2 (Upper)
        • GMT Fuse Block
    • Cordex System Controller (CXC)
      • CXCM4 Overview
      • Front Panel
        • Display
        • LEDs
          • Alarm Conditions
          • Progress and Status Indication
        • Reset
        • Ethernet Port
        • RS-232 Serial (Craft) Port
      • Analog Input Channels
        • Voltage Inputs
        • Current Inputs
        • Temperature Inputs
      • Digital Input Channels
      • Alarm and Control Output Relays
        • LVD Control (External Option)
      • System Fail Alarm/Relay
      • Network Connection and Remote Communications
    • Cordex 48-3.6kW Rectifiers
      • Rectifier Overview
      • Remote Control
      • Rectifier Front Panel
        • LEDs
          • AC ON
          • DC ON
          • ALARM
          • LED Activity During Software Upload
          • LED Activity During ‘Locate Module’ Command from CXC
        • Mechanical
      • Rectifier Rear Panel
      • True Module Fail Alarm
      • Heat Dissipation
      • Over Temperature Protection
      • Wide AC Range
      • AC Inrush/Transient Suppression
      • Soft Start
      • Start Delay
      • Current Limit/Short Circuit Protection
      • Power Limiting
      • High Voltage Shutdown (HVSD)
      • Battery Eliminator Operation
  • Inspection
    • Packing Materials
      • Returns for Service
    • Check for Damage
    • General Receipt of Shipment
      • Racks
      • Rectifiers (Purchased Separately)
      • Miscellaneous Small Parts
      • Batteries (Purchased Separately)
  • Installation
    • Safety Precautions
    • Tools Required
    • Power System Assembly and Mounting
      • Rack Mounted Systems
      • Floor Mounted Systems
      • Half-Rack/Battery Mounted Systems
    • Rectifier Module Insertion/Removal
    • Battery Installation
      • Preparation/Mounting
      • Installation of Batteries
  • Wiring
    • Grounding
    • AC Feeder Protection/Sizing
    • AC Input Connections
    • DC Output Connections
      • Battery Connections
        • Back-To-Back Connections
      • Load Distribution
        • AM Breakers
        • GMT Fuses
    • DC-DC Converter Connections
      • Re-Configure Split Tier Distribution
      • Argus CSM02 Six-Module Converter Shelf Installation Method O
        • Installation Procedure
          • Preparation
          • Converter Output Cabling (-GND Connection)
          • Converter Output Cabling (+24V HOT Connection)
          • Converter Input Cabling (+GND Connection)
          • Converter Input Cabling (-48V Connection)
        • Converter Fail Alarm
          • Locate #18 AWG wire with tag #17
          • Locate #18 AWG wire with tag #18
        • Final Steps
    • Controller I/O Connections
      • Analog Inputs
      • Digital Inputs
        • Connection Method
        • Programming the Digital Input
      • Relay Outputs
        • System Fail Relay
        • LVD Control
      • CAN Port
    • Network Connection and Remote Communications via CXC
      • Ethernet Port for Network Connection (Standard Network Cable
      • Ethernet Port for Local Connection (Crossover Cable)
  • System Startup
    • Check System Connections
    • Verify AC and Power the Rectifier Shelf
    • Check Battery Polarity and Connect
    • CXC Reset
  • Operation
    • Main Rectifier States
      • Off State
      • Start Delay State
      • Soft Start State
      • Normal Operation State
      • Turning Off State
    • Main Rectifier Modes
      • Output Voltage Modes
      • Output Current/Power Modes
    • Factory Ranges and Defaults
  • Maintenance
    • Fan Replacement
    • MOV Replacement
  • Argus Conventions
    • Numbering System
    • Acronyms and Definitions
• Outline Drawing
• Schematic, Power System
• Customer Connections
• Warranty and Service
• Service Centers