Document Outline

• Introduction
  • Shipping and storage; product inspection
  • Warranty
  • Application domain the operating manual
  • Measures to be taken before sending your device to the manuf
  • Supplementary operating instructions regarding the HART( interface
• Steps prior to operation
  • Installation and servicing
  • Safety advisory for the user
  • Hazard warnings
    • Danger
    • Warning
    • Caution
    • Note
  • Proper use of the device
  • Returning your flowmeter for servicing or calibration
  • Replacement of the transmitter electronics
• Identification
• The CMU sensor
  • Application domain of the CMU sensor
  • Mode of operation
    • Measuring principle
    • System configuration
    • Input
  • Custody transfer operations
  • Performance characteristics of the CMU sensor
    • Reference conditions
    • CMU flow ranges
    • Density measurement
    • Accuracy
    • Pressure loss CMU
    • Ambient temperature
    • Ambient temperature range
    • Storage temperature
    • Climatic category
    • Ingress protection
  • Operating conditions
    • Installation
    • Installation positions
    • Assessment of installation position
    • Pressure surges
    • Using the device with hazardous fluids
    • Vibration stability
  • Process conditions
    • Process temperature
    • Physical state
    • Viscosity
    • Gas content
    • Process temperature range
    • Process pressure range
    • Outlet pressure
  • Connection to the transmitter
    • Integral mount configuration
    • Remote mount configuration
  • Construction details
    • Dimensions and weight
    • Dimension drawing for the types CMU-C to CMU-H
      • Standard version dimension drawing
      • Integral mount version up to 150 °C (302 °F)
      • Remote mount version dimension drawing
      • Remote mount version dimension drawing up to 180 °C (356 °F)
      • Remote mount version dimension drawing up to 260 °C (500 °F)
    • Dimension drawing for the types CMU-J to CMU-R
      • Standard version dimension drawing
      • Integral mount configuration up to 180 °C (356°F)
      • Remote mount version dimension drawing
      • Remote mount version dimension drawing up to 180 °C (356°F)
      • Remote mount version up to 260 °C (500°F)
    • Heater dimension drawings for CMU-J up to CMU-R
      • Heater for standard version
      • Heater for integral mount version up to 150 °C (302°F)
      • Heater for remote mount version
      • Heater for remote mount version up to 180 °C (356°F)
      • Heater for remote mount version up to 260 °C (500 °F)
    • Material
  • Sensor CMU approvals
    • Explosion protection
    • CE marking
    • Custody transfer operations
• Commissioning
  • Zero point calibration
  • Startup conditions
• Application domain of the CT transmitter
• CT transmitter: mode of operation and configuration
  • Measuring principle
  • System configuration
    • DSB data memory module
• Input
  • Measured variable
  • Measuring range
• Output
  • Output signal
  • Failure signal
  • Load
  • Damping
  • Low flow cutoff
• CT performance characteristics
  • Reference conditions
  • Measured error
  • Repeatability error
  • Influence of ambient temperature
• CT operating conditions
  • Installation conditions and cable glands
  • Environmental conditions
    • Ambient temperature
    • Ambient temperature range
    • Storage temperature
    • Ingress protection
  • Process conditions
    • Fluid temperature
    • Physical state
    • Viscosity
    • Fluid temperature limit
    • Flow rate limit
    • Pressure loss
• Construction details
  • Type of construction/dimensions
  • Weight
  • Material
  • End connection
  • Electrical connection
    • CT connections
    • Wiring diagram
      • Wiring diagram for the integral mount configuration of senso
      • Wiring diagram for the remote mount configuration of sensor
    • HART®
    • Communication via SensorPort
• Control unit BE2
  • Introduction
  • Display
  • Operating modes
  • Operation
    • Operator interface
    • The keys and their functions
    • Functional classes, functions and parameters
      • Selection window/make a selection
      • Input window/modify a value
      • Passwords
• CT transmitter functions
  • MEASURED VALUES functional class
    • Mass flow
    • Volume flow
    • Counter forward
    • Counter reverse
    • Density
    • Temperature
    • Elapsed time
    • Mass flow + Counter forward
    • Mass flow + Density
    • Mass flow + Temperature
    • Volume flow + Counter forward
    • Volume flow + Density
    • Display mode during startup
    • Raw values
  • PASSWORD functional class
    • Customer password
    • Change customer password
    • Service password
  • COUNTER functional class
    • Unit of counters
    • Reset counters
  • MEASUREMENT PROCESSING functional class
    • Damping
    • Low flow cut-off
    • Low flow cut-off hysteresis
    • Zero point calibration
  • FLOW functional class
    • Mass flow QM unit
    • Mass flow QM range
    • Mass flow QM limit MIN
    • Mass flow QM limit MAX
    • Mass flow QM limit hysteresis
    • Volume flow QV unit
    • Volume flow QV range
  • DENSITY functional class
    • Density measurement on/off
    • Density unit
    • Density lower-range value
    • Density upper-range value
    • Density limit MIN
    • Density limit MAX
    • Density limit hysteresis
    • Density limit for empty pipe
    • Fixed density
    • Reference/process density display
    • Temperature coefficient
    • Reference temperature
    • Reference pressure
  • TEMPERATURE functional class
    • Temperature unit
    • Temperature lower-range value
    • Temperature upper-range value
    • Temperature limit MIN
    • Temperature limit MAX
    • Max. measured temperature
  • PULSE OUTPUT functional class
    • Pulse or frequency output
    • Pulse output unit
    • Pulse value
    • Pulse width
  • STATUS functional class
    • Status output active state
    • Status output 1 assignment
    • Status output 2 assignment
    • Binary input assignment
  • CURRENT OUTPUTS functional class
    • Current output I1 0/4 to 20 mA
    • Current output I1 alarm
    • Current output I1 assignment
    • Current output I2 0/4 to 20 mA
    • Current output I2 alarm
    • Current output I2 assignment
  • SIMULATION functional class
    • Simulation on/off
    • Direct simulation
    • Measured value simulation
      • Simulation mass flow QM abs
      • Density simulation
      • Temperature measurement simulation
    • Direct simulation of outputs
      • Status output simulation
      • Pulse output simulation
      • Simulation current output I1
      • Simulation current output I2
  • SELF-TEST function class
    • Sensor test on/off
    • Max. deviation of excitation
    • Self-test calibration
    • Monitoring of sensor amplitude and excitation current
  • UMC TRANSMITTER SETTINGS functional class
    • Language
    • Serial number
    • Software version
    • Reset system error
    • Profibus/Modbus device address
  • SENSOR SETTINGS functional class
    • Sensor constant C
    • Sensor material
    • Flow direction
• Use of the CT for custody transfer operations
  • Programming the transmitter
  • Binary input (resetter)
  • Self-test error
  • Verification stamp/stamp position
  • HART® communication in Custody transfer mode
• CT transmitter error messages
  • Standard operating mode
  • Custody transfer mode
  • List of error messages
    • Display of self-test errors
    • Display of system error
• Certificates and approvals
• Standards and authorizations
  • General standards and directives
  • Electromagnetic compatibility
  • Ex-Approval transmitter
• Decontamination certificate for device cleaning