intimus 2000 C - Manual (Page 5)

MATERIAL JAM IN MACHINE:
(Auto-stop-function)
If too much material is fed in, causing a jam, the
machine will respond as follows:
- The cutting system blocks and stops.
Cutting mechanism halts, then runs one step in
reverse (material will be released) and stops.
- The motor shuts down automatically.
- The pilot lamp (4) (fig. 1) lights up.
Proceed as follows:
- Turn the function switch (1) (fig. 1) briefly to
position „ “ (material will be released), then in
position „ “.
- The pilot lamp (4) (fig. 1) goes out.
Paper jam in the paper feed slot (6)
- Tear off the excess paper over the feed slot
and then turn the function switch (1) (fig. 1) to
position „ “.
- The cutting system then runs forward and shreds
the paper remaining in the cutter.
- Continue shredding, feeding smaller quantities
of paper.
Material jam in the CD/DVD feed slot (7)
- Remove the returned material.
Take care when removing material as
sharp edges may cause injury.
- Turn the function switch (1) (fig. 1) in position „
“.
- The remaining material to be shredded is then
fed to the cutting system again.
- Once the remaining material has been shred-
ded, continue shredding, feeding the correct
quantities.
- If required, switch the cutting system alternately
to forward and reverse until all of the material
has been run through the cutting system and
shredded.
Wait each time until the motor stops
before switching direction (position
„ “).
MOTOR PROTECTION:
The motor shuts down automatically, should it
become overloaded. The pilot lamp (5) (fig. 1)
lights up. Turn the machine off with the function
switch (1) (fig. 1) (position „ “).
Allow the motor to cool down for 25 to 30 minutes
(depending upon room temperature) and then
continue shredding.
CHECKLIST IN CASE OF MALFUNCTIONS:
If the device does not function, check the follo-
wing:
- Is the plug connected to the mains?
- Is the function switch (1) on?
- is the receptacle placed properly under the
machine?
- is the receptacle full?
The receptacle has to be emptied.
- is there a material jam in the machine?
Follow the instructions under ”MATERIAL
JAM”
- has the motor been overloaded?
Wait until the motor has cooled, and then re-
start.
If none of the above applies, please contact
your dealer.
2
93403 1 08/13
1000S 1000C 2000S 2000C
MAINTENANCE / DISPOSING
CLEANING THE PHOTOCELLS (Fig. 4):
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is pos-
sible that the machine will not turn off, due to the
broken light barrier.
To remove these paper strips and also to clean
the photocell, pass another sheet of paper through
the feed slot, or switch the machine to reverse and
wipe both „eyes“ of the photocell with a brush.
TECHNICAL DATA MALFUNCTIONS
ACCESSORIES
GB
MAINTANENCE OF THE
CUTTING MECHANISM (3,8x48 mm):
Cross-cut cutting mechanism should be
oiled regular after a certain operating time
to maintain the cutting performance.
This can be easily accomplished if you
pour special shredder oil (Order-No. see
ACCESSORIES) as shown on a sheet of
paper and feed it through the inlet guide
to the cutting mechanism (fig. 5).
TIP FOR ENERGY SAVING:
Please make sure that the shredder is switched
off over night (Turn the function switch (1) (fig. 1)
in position „ “).
DISPOSING OF THE MACHINE:
Dispose of the machine in an
environmentally sound fashion at the
end of its useful service life. Do not
dispose of any of the parts included
in the machine or its packaging with
household trash.
Description Order-No.
Plastic bag, 300 x 300 x 700 x 0,018 mm 99925
Lubricant, 110 ml bottle 88035
Note: For orders of special accessories and spare parts, please contact your dealer.
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
fig. 4
fig. 5
5
Cutting width:
1000S: 4 mm
1000C: 3.8x48 mm
2000S: 4 mm
2000C: 3.8x48 mm
Cutting capacity paper:
1000S: 10-12 sheets (70g/m 2 )
1000C: 7-9 sheets (70g/m 2 )
2000S: 14-16 sheets (70g/m 2 )
2000C: 9-12 sheets (70g/m 2 )
Cutting capacity
Credit cards/CD’s/DVD’s: feed one at a time
Supply voltage: 230V/50Hz
240V/50Hz
120V/60Hz
Pre-fusing: 10 amps (slow-blow)
Noise level:
1000S/C: approx. 64 dB(A)
2000S/C: approx. 66 dB(A)
Power:
1000S/C: 0.35 kW
2000S/C: 0.39 kW
Intermittent operation: 8 min ON
30 min OFF
Dimensions:
1000S/C:
Width: 350 mm
Depth: 250 mm
Height: 560 mm
2000S/C:
Width: 400 mm
Depth: 300 mm
Height: 600 mm
Weight:
1000S: ca. 7 kg
1000C: ca. 8 kg
2000S: ca. 10 kg
2000C: ca. 12 kg