Diamond Products Fast-Cut SLR User Manual
Page 3
3
Thank you for purchasing Diamond Products!
Congratulations on choosing a Diamond Products Fast-Cut cutoff
saw! We are confident that you will be satisfied with this modern
piece of equipment. The Diamond Products Fast-Cut features
specially designed high-performance engine with outstanding
power-to-weight ratios, for heavy-duty yet lightweight tools.
Other advantages of the Diamond Products Fast-Cut:
• Sturdy construction and high reliability.
• Maintenance‑free electronic ignition, hermetically sealed to
protect against dust and moisture.
• Vibration damping with the Diamond Products 2-mass system
(D2M) for tireless working even when guiding the Fast‑Cut by
hand.
• Five‑stage air‑filter system for reliable working even under very
dusty conditions.
• Two options for mounting the cutter attachment: Either centrally,
for good balance when guiding the unit manually, or on the side,
for flush cuts along walls or curbsides or horizontally directly
above the ground.
• Extensive range of resin-bonded and diamond grit cutting discs,
trolley with dust catcher, and systems for supplying water to the
disc.
The following industrial property rights apply:
US 08510690, SE 95027298, SE 95027306, IT 95000653,
IT 95000654, GBM 9412558, GBM 9412559.
We want you to be satisfied with your Diamond Products prod-
uct.
In order to guarantee the optimal function and performance of your
Fast-Cut and to ensure your personal safety we would request you
to perform the following:
Read this instruction manual carefully before putting the
Fast-Cut into operation for the first time, and strictly observe
the safety regulations! Failure to observe these precautions
can lead to severe injury or death!
Only for FC7312, FC7314: The Emissions Compliance Period
referred to on the emission Compliance label indicates the num-
ber of operating hours for which the engine has been shown to
meet federal emissions requirements.
Category C= 50 hours, B= 125 hours, and A= 300 hours.
Packing
Your Diamond Products Fast-Cut is packed in a cardboard box
to prevent shipping damage.
Cardboard is a basic raw material and is consequently reuseable
or suitable for recycling (waste paper recycling).
Table of contents
Page
Packing ................................................................................3
Delivery inventory ..............................................................4
Symbols ...............................................................................4
SAFETY PREcAUTIONS
Intended use ...................................................................5
General precautions .......................................................5
Protective equipment ...................................................5-6
Fuels / Refuelling ............................................................6
Putting into operation ......................................................6
Cutting discs ...................................................................7
Kickback and lock-in .......................................................8
Working behavior / Method of working ............................8
Always observe the following when using
synthetic resin cutting discs .............................................9
Cutting metal ...................................................................9
Cutting masonry and concrete ...................................9-10
Transport and storage ...................................................10
Maintenance ................................................................. 11
First aid ......................................................................... 11
Disposal and environmental protection ......................... 11
Technical data ...................................................................12
Denomination of components .........................................13
PUTTING INTO OPERATION
Mounting the cutting disc ...............................................14
Tightening the V-belt / Checking V-belt tension ............15
Installing the pressure water system .......................15-16
Fuels / Refuelling .....................................................16-17
Starting the engine ........................................................18
Cold-starting .................................................................19
Warm-starting ...............................................................19
Stop engine ...................................................................19
Adjusting the carburetor ..................................................20
MAINTENANcE
Changing the V-belt ......................................................21
Cleaning the protection hood ........................................22
Cleaning / changing the air filter ..............................22-23
Replacing the spark plug ..............................................24
Replacing the suction head ..........................................24
Replacing the starter cable ...........................................25
Replacing the return spring ...........................................26
Instructions for periodic maintenance ...........................30
cutting attachment in central / side position .................27
Repositioning the cutting attachment .......................27-28
Replacing/cleaning the spark arrester screen ..............28
Service, spare parts and guarantee ...........................29-30
Troubleshooting ...............................................................30