FEC DSP1500 (SAN3) User Manual
Page 13
enFORCE
Operation Manual
PAGE 4 - 13
Chapter 4: System Setup and Wiring
WORK SELECT 0 thru 4: Parameter Select signal (Normally Open)
These 5 inputs [WORK SELECT 1-4] form a binary code which is capable of selecting
up to 32 different sets of press parameters.
*Allow at least 10ms from the time this signal is turned on before turning on the START signal.
Do not turn this signal off at least until BUSY goes “HIGH”.
WORK
SELECT 4
WORK
SELECT 3
WORK
SELECT 2
WORK
SELECT 1
WORK
SELECT 0
Param
No.
MANUAL mode
OFF (OPEN) OFF (OPEN) OFF (OPEN) OFF (OPEN) OFF (OPEN)
１
H o m e - p o s i t i o n s e a r c h
OFF (OPEN) OFF (OPEN) OFF (OPEN) OFF (OPEN)
ON
２
H o m e - p o s i t i o n r e t u r n
OFF (OPEN) OFF (OPEN) OFF (OPEN)
ON
OFF (OPEN)
３
D e s c e n t h i g h s p e e d j o g
OFF (OPEN) OFF (OPEN) OFF (OPEN)
ON
ON
４
A sce n t h i g h sp e e d j o g
OFF (OPEN) OFF (OPEN)
ON
OFF (OPEN) OFF (OPEN)
５
Desc ent middle speed jog
OFF (OPEN) OFF (OPEN)
ON
OFF (OPEN)
ON
６
As cent mi ddl e sp ee d j og
OFF (OPEN) OFF (OPEN)
ON
ON
OFF (OPEN)
７
D e s c e n t l ow s p e e d j o g
OFF (OPEN) OFF (OPEN)
ON
ON
ON
８
A s c e n t l o w s p e e d j o g
OFF (OPEN)
ON
OFF (OPEN) OFF (OPEN) OFF (OPEN)
９
( H om e- p os i t i o n s e a r ch )
OFF (OPEN)
ON
OFF (OPEN) OFF (OPEN)
ON
１０
( H o m e - p o s i t i o n r e t u r n )
OFF
(OPEN) ON OFF
(OPEN)
ON OFF
(OPEN)
１１
(D esc en t hi gh s pe ed jo g)
OFF
(OPEN) ON OFF
(OPEN)
ON
ON １２
(A sc ent h igh s pee d j og)
OFF (OPEN)
ON
ON
OFF (OPEN) OFF (OPEN)
１３
(Descent m iddle speed jog)
OFF (OPEN)
ON
ON
OFF (OPEN)
ON
１４
(As c en t mid dl e spe e d jo g)
OFF
(OPEN) ON
ON
ON OFF
(OPEN)
１５
(D es ce nt lo w sp ee d j og )
OFF
(OPEN)
ON ON ON ON
１６
( A sc e n t l ow s p e e d j o g)
ON
OFF (OPEN) OFF (OPEN) OFF (OPEN) OFF (OPEN)
１７
( H om e- p os i t i o n s e a r ch )
ON
OFF (OPEN) OFF (OPEN) OFF (OPEN)
ON
１８
( H o m e - p o s i t i o n r e t u r n )
ON
OFF (OPEN) OFF (OPEN)
ON
OFF (OPEN)
１９
(D esc en t hi gh s pe ed jo g)
ON
OFF (OPEN) OFF (OPEN)
ON
ON
２０
(A sc ent h igh s pee d j og)
ON
OFF (OPEN)
ON
OFF (OPEN) OFF (OPEN)
２１
(D esc en t hi gh s pe ed jo g)
ON
OFF (OPEN)
ON
OFF (OPEN)
ON
２２
(As c en t mid dl e spe e d jo g)
ON OFF
(OPEN) ON
ON OFF
(OPEN)
２３
(D es ce nt lo w sp ee d j og )
ON OFF
(OPEN) ON
ON
ON ２４
( A sc e n t l ow s p e e d j o g)
ON
ON
OFF (OPEN) OFF (OPEN) OFF (OPEN)
２５
( H om e- p os i t i o n s e a r ch )
ON
ON
OFF (OPEN) OFF (OPEN)
ON
２６
( H o m e - p o s i ti o n r e t u r n )
ON
ON OFF
(OPEN)
ON OFF
(OPEN)
２７
(D esc en t hi gh s pe ed jo g)
ON ON
OFF
(OPEN)
ON ON
２８
(A sc ent h igh s pee d j og)
ON ON ON
OFF
(OPEN) OFF
(OPEN)
２９
(Descent middle speed jog)
ON ON ON
OFF
(OPEN)
ON
３０
(Ascent middle speed jog)
ON ON ON ON
OFF
(OPEN)
３１
(Descent low speed jog)
ON ON ON ON ON
３２
( A sc e nt l ow s p e e d j o g)
If the start signal is turned “ON” while in MANUAL mode, the press will perform the function
defined in the MANUAL operation of the selected Parameter Number; “Home-position search”,
“Home-position return”, “Descent jog” (Advance) and “Ascent jog” (Return)”.
The speed of the operation of MANUAL mode is set in the Data Number OE: MANUAL SPEED
system parameter. (See Page 6-23）The speed of the “Home-position search”, “Home-position
return”, “High speed jog” is set to this set value.
If a value greater than 10mm/sec. is entered, the system will limit Home Position
Search speed to 10mm/sec.
The speed of the “middle speed jog” is set to 1/10 of this set value or the tool’s minimum speed.
The speed of the “low speed jog” is set to 1/10 of this set value or the tool’s minimum speed.
On a “Home Position Search”, the ascent (return) operation operates first and
when the CCW limit sensor turns OFF, the operation changes to descent
(advance) operation. After the CCW limit sensor turns ON again, the motor will
advance until the resolver location (in pulses) is at 0. This point is set to the
zero point and becomes the home position. (See Section 7.2.3.2)