Warner Electric CBPC-3590 - Manual (Page 11)

Warner Electric • 800-825-9050 P-291-1 • 819-0526 11
q 2. Re-tighten encoder bracket securely.
q 3 . Proceed to step 1 of the start-up procedure,
page 9 to recalibrate the system .
Note: If in doubt about encoder positioning, refer to
new encoder installation procedure, page 6.
If unit has problems such as “windmilling” program
default needed, do the following steps:
q a. Press the RUN/PGM key on the keypad.
q b. Enter 1, 0, 0, 0 and then press the down arrow
repeatedly until the end display reads: “t8.rdy”.
q c. Press the arrow right button.
q d. Press the RUN/PGM key.
q e . Proceed to step 1 of the start-up procedure
on page 9 to recalibrate the system .
This completes the installation and set-up of the
CBPC-3590 control. Close and latch the control
securely .
As the controller has been designed as an improved
version of the CBC1500-AHFC with additional
features and improved performance and reliability,
programming of the various parameters should only
be accomplished by qualified personnel .
To Enter the programming mode, follow the steps
below:
Open the controller front cover for access to the
keypad/display. Press the RUN PGM key on the
keypad/display
Display will show LOC. 0
Then press 1, 0, 0, 0
Display will show LOC. 1000
This has now placed you in the programming mode
where various parameters can be changed by using
the down arrow key to increment through the various
parameters .
Programming Functions:
Default Settings
Default
Press Display Value Function
↓ h xxx -- Home Position
↓ bd. xx -- Brake Distance, PPR
↓ bdAue . 3 3 Cycles Averaged
↓ cc. 0.5000 0.5000 Count Correction
↓ dP. oFF oFF Decimal Point
↓ FrSt. oN oN Front Panel Reset
↓ PLoc. oFF oFF Panel Lock
↓ CrEt. oFF oFF Count Retention
↓ ArSt. oN oN Auto Reset
↓ o1. 0.20 0.20 Start Signal, ms
↓ o2. 0.01 0.01 Early Warning, ms
↓ o3. 0.20 0.20 Stop Signal, ms
↓ o4. 0.10 0.10 Zero Speed, ms
↓ o5. 0.05 0.05 Zero Speed + delay 1, ms
↓ o6. 0.05 0.05 Zero Speed + delay 2, ms
↓ o8. LatCH LatCH Batch Auto Reset
↓ d1. 0.10 0.10 Delay 1, ms
↓ d2. 0.01 0.01 Delay 2, ms
↓ 05P .25 .25 Zero Speed Window, sec
↓ 5 -.-.-.-.-.-. -.-.-.-.-.-. Start Release
↓ L - .- .- .- .- .- . - .- .- .- .- .- . Move Preset Release
↓ E - .- .- .- .- .- . - .- .- .- .- .- . Early Warning Release
↓ r - .- .- .- .- .- . - .- .- .- .- .- . Reset Release
↓ bd. OFF OFF Baud Rate
↓ Par. None None Parity
↓ PFr. 80 80 Output Frequency, Hz.
↓ cPr. 90 90 Clutch Output Percentage
↓ bPr. 75 75 Brake Output Percentage
↓ JPr. 40 40 Jog Output Percentage
↓ cBt 15 15 Clutch Boost Percentage **
↓ bBt 40 40 Brake Boost Percentage **
↓ Id.no. xxx xxx Unit Number (Up to 3 digits)
↓ t0. rdy rdy Keyboard test
↓ t1 . rdy rdy RAM test
↓ t2 . rdy rdy Inputs test
↓ t3 . rdy rdy Outputs test
↓ t4 . rdy rdy Display test
↓ t5. rdy rdy Memory test
↓ t6. rdy rdy Date Code
↓ t7 . rdy rdy Serial Test
↓ t8. rdy rdy Reset Default Program
** Only when the OEX add-on board is installed in the CBPC-3590 are
these two functions active and operational for programming.