Lincoln Electric IM621 Mobiflex 200-M K1653-1,-2 - Manual (Page 11)

A-4 INSTALLATION
MObIFLEX 200-M
A-4
MOUNTING THE EXTRACTION ARM
(continued)
Place the other rubber seal around base of the arm
tube. MOUNT THE ARM IN THE VERTICAL POSI-
TION! Rotate the hinge rod so the stop pin is in the
back, and mount the arm (Fig. 4, Item A) on the hinge
rod (Fig. 4, Item B); use the two (1 3/4”) bolts and nuts
in the two connecting holes as shown in the inset of
Fig. 4.
Leave the tape and plastic packaging on the
extraction arm sections until the arm is complete-
ly installed (including mounting the hood). The arm is
spring-balanced to compensate for the weight of the
hood and will spring out quickly if it is not mounted
securely, with the hood in place.
Position one 8” rubber seal (Fig. 5, Item B) and the
flexible hose supplied with the arm (Fig. 5, Item C)
onto the hood end of the arm (Fig. 5, Item A).
Put the last rubber seal on the hood connection.
Mount the hood to the arm.
Remove the plastic and tape from the arm sections.
Snap the “hose running guard” onto the middle hinge
section so the “nose” end faces the base of the arm
as shown in Figure 6.
ADJUSTING THE bALANCE AND
MOVEMENT OF THE ARM
Do not attempt to change the spring tension. Springs
are factory set and once released, cannot be reset in
the field. Balance and movement adjustments are only
made through adjustments of the friction connections.
When installing the arm, adjust the friction connec-
tions to convenient settings. These connections are
located at the base hinge, at the front and back of the
middle hinge, and in two directions at the hood hinge.
Reference the maintenance section of the instruction
manual for the LFA Extraction Arm for details. After
adjusting the friction connections and installing any
lamp options that you have purchased, seal all con-
necting hoses with the rubber seals as described ear-
lier.
INSTALLING THE LAMP OPTIONS
AND ARC SENSOR
Each of the lamp option packages provides conve-
nient hood-mounted switches for both the light and
Mobiflex 200-M.
Either the optional K1669-1 Lamp Kit or K1706-1
Work Lamp package can be combined with a K1670-1
Automatic start/stop arc sensor to automatically switch
the Mobiflex unit on and off when the sensor detects
an arc. The K1669-3 Lamp Kit and K1706-2 Work
Lamp come with the Arc Sensor pre-installed in the
lamp housing.
B C A B C D Client: Lincoln / Euromate Client no/project no: 123380/170241-4 Date: 03.12.1997 Drawing no/archive no:lusUL310.eps Version no: 1 Illustrator: Jos Taabe Description: montage afzuigkap.
B
C
A
B
C
D
Client: Lincoln / Euromate
Client no/project no: 123380/170241-4
Date: 03.12.1997
Drawing no/archive no:lusUL310.eps
Version no: 1
Illustrator: Jos Taabe
Description:
montage afzuigkap.
Fig. 5
B A A Client: Lincoln / Euromate Client no/project no: 123380/170241-4 Date: 03.12.1997 Drawing no/archive no:lusUL303.eps Version no: 1 Illustrator: Jos Taabe Description: plaatsen arm mobiel.
B
A
A
Client: Lincoln / Euromate
Client no/project no: 123380/170241-4
Date: 03.12.1997
Drawing no/archive no:lusUL303.eps
Version no: 1
Illustrator: Jos Taabe
Description:
plaatsen arm mobiel.
Fig. 4
C
F B 360 ° B C A A C C
C(2x) A A C(2x) A
C
B
Client: Lincoln / Euromate Client no/project no: 123380/170241-4 Date: 03.12.1997 Drawing no/archive no:lusUL312.eps Version no: 1 Illustrator: Jos Taabe Description: plaatsen afstandsbeugel.
C
F
B
360 °
B
C
A A C C
C(2x) A
A
C(2x)
A
C
B
Client: Lincoln / Euromate
Client no/project no: 123380/170241-4
Date: 03.12.1997
Drawing no/archive no:lusUL312.eps
Version no: 1
Illustrator: Jos Taabe
Description:
plaatsen afstandsbeugel.
Fig. 6
CAUTION
WARNING