NSi Industries DLC400BP - Manual (Page 3)

The display will only show the last scheduled event for
CH1. To view the last schedule event for other channels,
simply press the
EVENT key again. If there is no sched-
ule programmed for a specific channel, the display will
show
—:—
NOTES:
1. Unit will go to RUN MODE automatically if no
key is pressed for 5 minutes.
2. Unit has a look back feature. If you have just fin-
ished setting the unit and an output is to be
updated, press the EVENT key. Unit will auto-
matically pick up the last schedule.
3. Clear all memory. To clear all memory, while in
the RUN mode, press ENTER , display will
show:
Press EVENT , the display will show:
Press ENTER briefly and everything in the timer
memory is wiped off including real time and date.
12HOUR will flash.
9
MO TU WE TH FR SA SU H
CH1 2 3 4 ASTRO SEASON 1 2 3 4
ON
OFF
MO TU WE TH FR SA SU H
CH1 2 3 4 ASTRO SEASON 1 2 3 4
ON
OFF
MO TU WE TH FR SA SU H
CH1 2 3 4 ASTRO SEASON 1 2 3 4
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
2 3 4 ASTRO SEASON 1 2 3 4
2 3 4 ASTRO SEASON 1 2 3 4
TU WE TH FR SA SU H MO TU WE TH FR SA SU H
SIG2 CLK DATE SCH
SIG2 CLK DATE SCH
SIG2 CLK DATE SCH
4 ASTRO SEASON 1 2 3 4
C 4 ASTRO SEASON 1 2 3 4
C 3 4 ASTRO SEASON 1 2 3 4
C 3 4 ASTRO SEASON 1 2 3 4
WE TH FR SA SU H
4 ASTRO SEASON 1 2 3 4
O
WE TH FR SA SU H
ASTRO SEASON 1 2 3 4
O
MO TU WE TH FR SA SU H
CH1 2 3 4 ASTRO SEASON 1 2 3 4
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
SIG1 SIG2 CLK DATE SCH
SIG1 SIG2 CLK DATE SCH
ON
OFF
MO TU WE TH FR SA SU H
MO TU WE TH FR SA SU H
ON
OFF
MO TU WE TH FR SA SU H MO TU WE TH FR SA SU H
SIG1 SIG2 CLK DATE SCH
SIG1 SIG2 CLK DATE SCH
SIG1 SIG2 CLK DATE SCH
CH1 2 3 4 ASTRO SEASON 1 2 3 4
CH1 2 3 4 ASTRO SEASON 1 2 3 4
CH1 2 3 4 ASTRO SEASON 1 2 3 4
CH1 2 3 4 ASTRO SEASON 1 2 3 4
MO TU WE TH FR SA SU H
CH1 2 3 4 ASTRO SEASON 1 2 3 4
ON
OFF
MO TU WE TH FR SA SU H
CH1 2 3 4 ASTRO SEASON 1 2 3 4
ON
OFF
INSTRUCTIONS FOR INSTALLATION
CAUTION: Risk of Electric Shock – More than one disconnect switch may be required to de-energize the
equipment before servicing. Disconnect power at main panel prior to installing or servicing this lighting con-
trol or the equipment connected to it.
Connect in accordance with national and local electrical codes.
Installation by a licensed electrical contractor is recommended.
1. Remove unit cover before installing the unit.
2. Lift the deadfront above stud at top side and swing left to access the bottom holes for mounting.
3. Bring in the low voltage wires from the EPC2, remote override and 24VDC output, to the left compartment
of the unit and bring in all line voltage wires to right side of compartment.
4. Do not run low voltage wires and line wires through the same conduit.
5. Follow all local and NEC codes when wiring the unit.
6. Replace the deadfront after wiring and secure it in place.
7. When attaching conduit to enclosure, exercise care to align and support conduit in order to prevent unnec-
essary stress on enclosure.
8. Install 9V lithium battery supplied with the unit. Note: Unit should be connected to AC power within 24
hours of battery installation in order to prolong battery life which has 6 month cumulative backup for real
time and 7-10 year shelf life. REPLACE WITH ANOTHER 9V NON-RECHARGEABLE LITHIUM BATTERY
ONLY.
GROUNDING
Ensure that grounding is continuous and in proper electrical contact in all grounding conductors, metallic con-
duits and grounding terminals, and that the minimum size copper grounding conductors are #10 AWG if the cir-
cuit breaker or fuse is 30 or 40 amp, #12AWG if 20 amps, and #14 AWG if 15 amp, according to National
Electrical Code.
2
DLC400 5/1/07 11:26 AM Page 5