Document Outline

• 1 Introduction
  • 1.1 Preface
  • 1.2 Arrangement of the Documentation
  • 1.3 Typographical Conventions
• 2 Instrument Description
  • 2.1 Displays and Controls
  • 2.2 Analog Inputs
  • 2.3 Binary Inputs/Outputs
  • 2.4 Relay Outputs
  • 2.5 Counter/Integrators
    • 2.5.1 Counter
    • 2.5.2 Integrators
    • 2.5.3 Operating time counter
    • 2.5.4 High-speed counters
    • 2.5.5 Flow rate quantity
    • 2.5.6 Recording period of the counts
    • 2.5.7 Reset counters
    • 2.5.8 Response to setting the time
    • 2.5.9 Response to instrument reconfiguration
    • 2.5.10 Response to reconfiguration of the counters on the instrument
    • 2.5.11 Response to reconfiguration of counters with setup program
  • 2.6 Math/Logic Module
  • 2.7 Binary Signals
  • 2.8 Operating Modes
    • 2.8.1 Normal, Timed, and Event Mode
    • 2.8.2 Eco mode
  • 2.9 Data Storage
  • 2.10 Reading out Data
  • 2.11 Archiving and Evaluating Data
• 3 Operating Principle
  • 3.1 Operating Principle and Graphic Elements
  • 3.2 Operating Example
  • 3.3 Group and Plant Management (Batches)
• 4 Visualization
  • 4.1 Activating the Operator Level
  • 4.2 Overview of Header Lines
  • 4.3 Curve Presentation
  • 4.4 Bar Graph Presentation
  • 4.5 Text Picture Presentation
  • 4.6 Process Image Presentation
  • 4.7 Binary diagram presentation
  • 4.8 Reports
  • 4.9 Batches/Plants
    • 4.9.1 Current Batches
    • 4.9.2 Completed Batches
    • 4.9.3 Batch Control with Barcode Reader
  • 4.10 Counters and Integrators
  • 4.11 Comment Entry
• 5 Memory Presentation (History)
• 6 Alarm and Event Lists
  • 6.1 Call from One of the Visualization Modes
  • 6.2 Call from the Memory Presentation
  • 6.3 Symbols
• 7 Memory Manager
• 8 Device Manager
  • 8.1 Close Device Manager
  • 8.2 Log-in and Log-out
  • 8.3 Device information
  • 8.4 Device Audit Trail
  • 8.5 Configuration
  • 8.6 Parameterization
  • 8.7 Service
• 9 Parameterization
  • 9.1 Fine calibration
  • 9.2 Counters/integrators
  • 9.3 Date and time
  • 9.4 Batches/plants
• 10 Configuration - General
• 11 Configuration - Device Data
• 12 Configuration - Screen
  • 12.1 Brightness … Show text image
  • 12.2 Show process image … Bar code -> current batch
• 13 Configuration - Analog Inputs
  • 13.1 Sensor … Offset
  • 13.2 Filter Constant … Unit
  • 13.3 Comma format … Alarm Configuration
  • 13.4 Alarm configuration
    • 13.4.1 Status … Alarm text 2
    • 13.4.2 Alarm rejection
• 14 Configuration - Binary Inputs/Outputs
  • 14.1 Function … Alarm Configuration
  • 14.2 Alarm Configuration
• 15 Configuration - Relay
• 16 Configuration - External Analog Inputs
  • 16.1 Range Start … Alarm Configuration
  • 16.2 Alarm configuration
    • 16.2.1 Status … Alarm text 2
    • 16.2.2 Alarm rejection
• 17 Configuration - External Binary Inputs
  • 17.1 Channel Name … Alarm Configuration
  • 17.2 Alarm Configuration
• 18 Configuration - Groups
  • 18.1 Parameter
  • 18.2 Analog Channels
  • 18.3 Binary Channels
  • 18.4 Counters/Integrators
  • 18.5 Diagram View
  • 18.6 Normal Operation
  • 18.7 Event Mode
  • 18.8 Timed Mode
• 19 Configuration Report
  • 19.1 Total … Period
  • 19.2 External … Out of range
• 20 Configuration - Limit Monitoring
  • 20.1 Function … Alarm Configuration
  • 20.2 Alarm Configuration
• 21 Configuration - Counters/Integrators
  • 21.1 General Setting
  • 21.2 Function … Specific Setting
  • 21.3 Input Signal … Decimal Place
  • 21.4 Range Start … Alarm Configuration
  • 21.5 Alarm Configuration
• 22 Configuration - Interface
  • 22.1 Ethernet
  • 22.2 RS232/RS485
    • 22.2.1 General
    • 22.2.2 Modbus master
  • 22.3 RS232 for Barcode Reader
• 23 Configuration – Batches/Plants
  • 23.1 General Information on Batches
  • 23.2 General Plant Parameters
  • 23.3 Plant 1 — 3
    • 23.3.1 General
    • 23.3.2 Lines 1—10
  • 23.4 Final Remarks
• 24 Configuration - Date and Time
  • 24.1 Time Synch. … Daylight Saving Time
  • 24.2 Start Daylight Saving
  • 24.3 End Daylight Saving
• 25 Configuration - Undocumented Parameters
• 26 Entering text and values
  • 26.1 Text entry
    • 26.1.1 Entering characters
    • 26.1.2 Insert spaces
    • 26.1.3 Delete character
    • 26.1.4 Move cursor
    • 26.1.5 Enter text from text list
    • 26.1.6 Finish entry
    • 26.1.7 Reject entry
  • 26.2 Entry via selection field
  • 26.3 Entering values
    • 26.3.1 Whole numbers (integers)
    • 26.3.2 Real numbers (floating point)
• 27 Web server
  • 27.1 General
  • 27.2 Online Visualization (All Visualizations Except Batches)
  • 27.3 Three freely programmable HTML pages
  • 27.4 Online Visualization of Current Batch Reports
  • 27.5 4-Way View
• 28 Appendix
  • 28.1 Bar code
    • 28.1.1 Batch control
    • 28.1.2 Batch texts
• 29 Index