Document Outline

• Introduction
• Installation
  • Unpacking
  • Installation
  • Panel-Mounting
  • Cleaning
• -Field Upgrade Options
  • Options Modules and Functions
  • Preparing to Install or Remove Options Modules
  • Removing/Replacing Option Modules
  • Replacing the Instrument in its Housing
  • Auto Detection of Option Modules
  • Replacement of Power Supply or Input Boards
  • Data Recorder Board
  • Profiler Enabling
• Electrical Installation
  • Installation Considerations
  • AC Power Wiring - Neutral for 100 to 240V AC versions
  • Wire Isolation
  • Use of Shielded Cable
  • Noise Suppression at Source
  • Sensor Placement Thermocouple or RTD
  • Thermocouple Wire Identification Chart
  • Connections and Wiring
    • Power Connections
      • Power Connections - Mains Powered Instruments
      • Power Connections - 24/48V AC/DC Powered Instruments
    • Universal Input Connections
      • Universal Input Connections - Thermocouple T/C
      • Universal Input Connections – PT100 / NI120 RTD input
      • Universal Input Connections - Linear Volt, mV or mA input
    • Option Slot 1 Connections
      • Option Slot 1 – Single Relay Output Module
      • Option Slot 1 – Single SSR Driver Output Module
      • Option Slot 1 - Triac Output Module
      • Option Slot 1 - Linear Voltage or mADC Output module
    • Option Slot 2 Connections
      • Option Slot 2 – Single Relay Output Module
      • Option Slot 2 - Dual Relay Output Module
      • Option Slot 2 – Single SSR Driver Output Module
      • Option Slot 2 – Dual SSR Driver Output Module
      • Option Slot 2 - Triac Output Module
      • Option Slot 2 - Linear Voltage or mADC Output module
      • Option Slot 2 - Transmitter Power Supply Module
    • Option Slot 3 Connections
      • Option Slot 3 – Single Relay Output Module
      • Option Slot 3 - Dual Relay Output Module
      • Option Slot 3 – Single SSR Driver Output Module
      • Option Slot 3 – Dual SSR Driver Output Module
      • Option Slot 3 - Triac Output Module
      • Option Slot 3 - Linear Voltage or mADC Output module
      • Option Slot 3 - Transmitter Power Supply Module
    • Option Slot A Connections
      • Option Slot A Connections – Basic Auxiliary Input Module
      • Option Slot A Connections - Digital Input Module
      • Option Slot A Connections - Ethernet Communications Module
      • Option Slot A Connections - RS485 Serial Communications Module
    • Option Slot B Connections
      • Option Slot B Connections – Digital Input 2 Full Auxiliary Module
      • Option Slot B Connections – 1/4 DIN & 1/8 DIN Full Auxiliary Input Module
• Powering Up
  • Powering Up Procedure
  • Front Panel Overview
  • Display
  • LED Functions
  • Keypad
• Messages and Error Indications
  • Start-up Errors
  • Configuration Problem
• Input Problems
• Un-Calibrated Input Detection
• PV Over-range or Under-range Indication
• Auxiliary Input Over-range or Under-range Indication
• USB Data Transfer Problems
• Getting Help
• Second Level Support
• Third Level Support
• Configuration and Use
  • Operation Mode
    • Base, Trend & Profile Operating Screens
      • Navigating in Operator Mode
    • Adjusting the Local Setpoints
    • Adjusting the Setpoint Ramp Rate
    • Selecting Automatic or Manual Mode
    • Control Enable or Disable
  • Main Menu
    • Entry into the Main Menu
      • Navigating the Main Menu
    • Unlock Codes
  • Setup Wizard
    • Manual entry to the Setup Wizard
      • Navigating in the Setup Wizard
  • Supervisor Mode
    • Entry into Supervisor Mode
      • Navigating in Supervisor Mode
  • Configuration Menu
    • Entry into the Configuration Menu
      • Navigating the Configuration Menu
  • Input Configuration Sub-Menu
  • Control Configuration Sub-Menu
  • Output Configuration Sub-Menu
  • Alarm Configuration Sub-Menu
  • Communications Configuration Sub-Menu
  • Recorder Configuration Sub-Menu
  • Clock Configuration Sub-Menu
  • Display Configuration Sub-Menu
  • Lock Code View
  • Navigating Lock Code View
• Lost Lock Codes
  • Forcing Lock Code View
• Resetting To Defaults
• Automatic Tuning Menu
• Profiler Setup Menu
• Profiler Control Menu
• USB Menu
• Recorder Menu
• Product Information Mode
• Service Information Mode
• The USB Interface
  • Using the USB Port
    • USB Memory Stick Folders & Files
• The Data Recorder Option
  • Introduction
  • Changes To Operation Mode
  • Memory Use Bar Graph
• The Profiler Option
• Profiler Enabling
• Profile Components
• Profile Starting & Standard Segments
• Loops Segments
• Profile Running / Holding vs. Hold Segments
• The Auto-Hold Feature
• Profile Cycles & Repeat Sequences
• Power/Signal Lost Recovery Actions
• Profile End Actions
• Profile Abort Actions
• Manually Tuning Controllers
  • Single Control Tuning PID with Primary Output only
  • Dual Control Tuning PID with Primary and Secondary Outputs
  • PI Tuning Valve, Damper& Speed Controller
  • Fine Tuning.
• Serial Communications
  • Supported Protocols
  • RS485 Configuration
• Ethernet Configuration
• Supported Modbus Functions
• Function Descriptions
• Function 06 - Write Single Register
• Function 08 - Loopback Diagnostic Test
• Function 16 - Write Multiple Registers 0x10 Hex
• Function 23 Hex - Read / Write Multiple Registers 0x17 hex
• Exception Responses
• Modbus Parameters
• Universal Process Input Parameters
• Option Slot A Parameters
• Option Slot B Parameters
• Option Slot 1 Parameters
• Option Slot 2 Parameters
• Option Slot 3 Parameters
• Option Slot 4 Parameters
• Setpoint Parameters
• Control Parameters
• Alarm parameters
• Recorder & Clock Parameters
• Display Parameters
• Profiler Control & Status Parameters
• Profile Setup Over Modbus
• Instruction Sequence to create a profile at a specified profile position
• Instruction Sequence to edit an existing Profile Header
• Instruction Sequence to read a profile
• Creating Or Editing A Profile Header
• Creating, Editing or Inserting Segments
• Segment Data
• Deleting Profiles
• Delete A Segment
• Get Segments Remaining
• Edit Response Message From Instrument
• Command Response Data
• Read A Profile Header
• Read A Segment
• Segment Data
• Read Profile Name
• Read Profile Memory Status
• Read Profile Status
• Instrument Data
• Calibration
  • Calibration Reminder
  • Equipment Required For Checking or Calibrating the Universal Input
  • Calibration Check
  • Recalibration Procedure
• Appendix 1 – Glossary of Terms Used
• PC SOFTWARE
  • Using The Software
  • Instrument Configuration
  • Configuring Supervisor Mode
  • Configuring Enhanced Operator Mode
• Profile Creation And Editing
• Changing the Start-up Splash Screen
• Changing the Alternate Display Language
• Instrument Simulation
• Configuring The Connection
• Network Configuration For Modbus TCP Options
• Instrument Details
• Edit Modbus Settings
• Fixing An IP Address
• Appendix 2 - Specifications
  • Universal Process Input
    • General Input Specifications
    • Thermocouple Input
      • Thermocouple Types & Ranges
      • Thermocouple Performance
    • Resistance Temperature Detector RTD Input
      • RTD Types & Ranges
      • RTD Performance
    • DC Linear Input
      • DC Linear Types & Ranges
      • DC Linear Performance
  • Auxiliary Inputs
  • Auxiliary Input Performance
• Digital Inputs
• Digital Input Performance
• Output Specifications
• Single Relay Output Performance
• Dual Relay Output Performance
• Quad Relay Output Performance
• Single Dual SSR Driver Output Performance
• Dual SSR Driver Output Performance
• Triac Output Performance
• DC Linear Output Types & Ranges
• DC Linear Output Performance
• 24V Transmitter Power Supply Performance
• Communications
• PC Configuration Socket
• RS485
• Ethernet
• USB Socket
• Display
• Control Loop
• Data Recorder
• Profiler
• Alarms
• Conditions For Use
• Operating Conditions
• Standards
• Dimensions
• Appendix 3 - Product Coding