West Control Solutions ProVU 4 Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for ProVU 4 West Control Solutions
Manuals
| Recognized languages: | English |
|---|---|
| Pages: | 184 |
| Size: | 4.96 MB |
Show table of contents
Read manual
Document Outline
- Introduction
- Installation
- -Field Upgrade Options
- Electrical Installation
- Installation Considerations
- AC Power Wiring - Neutral for 100 to 240V AC versions
- Wire Isolation
- Use of Shielded Cable
- Noise Suppression at Source
- Sensor Placement Thermocouple or RTD
- Thermocouple Wire Identification Chart
- Connections and Wiring
- Power Connections
- Universal Input Connections
- Option Slot 1 Connections
- Option Slot 2 Connections
- Option Slot 2 – Single Relay Output Module
- Option Slot 2 - Dual Relay Output Module
- Option Slot 2 – Single SSR Driver Output Module
- Option Slot 2 – Dual SSR Driver Output Module
- Option Slot 2 - Triac Output Module
- Option Slot 2 - Linear Voltage or mADC Output module
- Option Slot 2 - Transmitter Power Supply Module
- Option Slot 3 Connections
- Option Slot 3 – Single Relay Output Module
- Option Slot 3 - Dual Relay Output Module
- Option Slot 3 – Single SSR Driver Output Module
- Option Slot 3 – Dual SSR Driver Output Module
- Option Slot 3 - Triac Output Module
- Option Slot 3 - Linear Voltage or mADC Output module
- Option Slot 3 - Transmitter Power Supply Module
- Option Slot A Connections
- Option Slot B Connections
- Powering Up
- Messages and Error Indications
- Input Problems
- Un-Calibrated Input Detection
- PV Over-range or Under-range Indication
- Auxiliary Input Over-range or Under-range Indication
- USB Data Transfer Problems
- Getting Help
- Second Level Support
- Third Level Support
- Configuration and Use
- Operation Mode
- Main Menu
- Setup Wizard
- Supervisor Mode
- Configuration Menu
- Input Configuration Sub-Menu
- Control Configuration Sub-Menu
- Output Configuration Sub-Menu
- Alarm Configuration Sub-Menu
- Communications Configuration Sub-Menu
- Recorder Configuration Sub-Menu
- Clock Configuration Sub-Menu
- Display Configuration Sub-Menu
- Lock Code View
- Navigating Lock Code View
- Lost Lock Codes
- Resetting To Defaults
- Automatic Tuning Menu
- Profiler Setup Menu
- Profiler Control Menu
- USB Menu
- Recorder Menu
- Product Information Mode
- Service Information Mode
- The USB Interface
- The Data Recorder Option
- The Profiler Option
- Profiler Enabling
- Profile Components
- Profile Starting & Standard Segments
- Loops Segments
- Profile Running / Holding vs. Hold Segments
- The Auto-Hold Feature
- Profile Cycles & Repeat Sequences
- Power/Signal Lost Recovery Actions
- Profile End Actions
- Profile Abort Actions
- Manually Tuning Controllers
- Serial Communications
- Ethernet Configuration
- Supported Modbus Functions
- Function Descriptions
- Function 06 - Write Single Register
- Function 08 - Loopback Diagnostic Test
- Function 16 - Write Multiple Registers 0x10 Hex
- Function 23 Hex - Read / Write Multiple Registers 0x17 hex
- Exception Responses
- Modbus Parameters
- Universal Process Input Parameters
- Option Slot A Parameters
- Option Slot B Parameters
- Option Slot 1 Parameters
- Option Slot 2 Parameters
- Option Slot 3 Parameters
- Option Slot 4 Parameters
- Setpoint Parameters
- Control Parameters
- Alarm parameters
- Recorder & Clock Parameters
- Display Parameters
- Profiler Control & Status Parameters
- Profile Setup Over Modbus
- Instruction Sequence to create a profile at a specified profile position
- Instruction Sequence to edit an existing Profile Header
- Instruction Sequence to read a profile
- Creating Or Editing A Profile Header
- Creating, Editing or Inserting Segments
- Segment Data
- Deleting Profiles
- Delete A Segment
- Get Segments Remaining
- Edit Response Message From Instrument
- Command Response Data
- Read A Profile Header
- Read A Segment
- Segment Data
- Read Profile Name
- Read Profile Memory Status
- Read Profile Status
- Instrument Data
- Calibration
- Appendix 1 – Glossary of Terms Used
- PC SOFTWARE
- Profile Creation And Editing
- Changing the Start-up Splash Screen
- Changing the Alternate Display Language
- Instrument Simulation
- Configuring The Connection
- Network Configuration For Modbus TCP Options
- Instrument Details
- Edit Modbus Settings
- Fixing An IP Address
- Appendix 2 - Specifications
- Digital Inputs
- Digital Input Performance
- Output Specifications
- Single Relay Output Performance
- Dual Relay Output Performance
- Quad Relay Output Performance
- Single Dual SSR Driver Output Performance
- Dual SSR Driver Output Performance
- Triac Output Performance
- DC Linear Output Types & Ranges
- DC Linear Output Performance
- 24V Transmitter Power Supply Performance
- Communications
- PC Configuration Socket
- RS485
- Ethernet
- USB Socket
- Display
- Control Loop
- Data Recorder
- Profiler
- Alarms
- Conditions For Use
- Operating Conditions
- Standards
- Dimensions
- Appendix 3 - Product Coding