Document Outline

• HP ProLiant ML350 Generation 5 Server User Guide
• Notice
• Contents
• Component identification
  • Front panel components
  • Front panel LEDs and buttons
  • Rear panel components
  • Rear panel LEDs and buttons
  • System board components
    • NMI jumper
    • System maintenance switch
  • System board LEDs
  • System LEDs and internal health LED combinations
  • SAS and SATA hard drive LEDs
  • SAS and SATA hard drive LED combinations
• Operations
  • Power up the server
  • Power down the server
  • Extend the server from the rack
  • Remove the server from the rack
  • Access the server rear panel (rack model)
  • Open or remove the tower bezel
  • Remove the access panel
  • Install the access panel
• Setup
  • Optional installation services
  • Optimum environment
    • Space and airflow requirements
    • Temperature requirements
    • Power requirements
    • Electrical grounding requirements
  • Rack planning resources
  • Rack warnings
  • Contents of the tower server shipping carton
  • Contents of the rack server shipping carton
  • Installing hardware options
  • Setting up a tower server
  • Installing the server into the rack
  • Powering up and configuring the server
  • Installing the operating system
  • Registering the server
• Hardware options installation
  • Introduction
  • Processor option
  • Memory options
    • Memory configurations
    • Advanced ECC memory
    • Online spare memory configuration
    • Installing FBDIMMs
  • Hard drive blank
  • SATA or SAS hard drive option
  • Removable media device options
    • Accessing the removable media cage
    • Identifying guide screws
    • Installing a half-height or full-height media device
    • Installing the full-height media device shipping screw
    • Installing a diskette drive
  • Redundant hot-plug power supply option
  • Expansion board options
    • Removing the expansion slot cover
    • Installing an expansion board
  • Parallel and second serial connector option
  • PCI-X expansion cage option
  • Redundant fan assembly option
  • Battery-backed write cache option
  • Tower-to-rack conversion option
• Cabling
  • Optional SATA or SAS cabling
  • Standard SATA hard drive cabling
  • Optical drive cabling
  • Optional ATA or ATAPI device cabling
• Configuration and utilities
  • Configuration tools
    • SmartStart software
      • SmartStart Scripting Toolkit
      • Configuration Replication Utility
    • ROM-Based Setup Utility
      • Using RBSU
      • Auto-configuration process
      • Boot options
      • BIOS Serial Console
    • Array Configuration Utility
    • Option ROM Configuration for Arrays
    • HP ProLiant Essentials Rapid Deployment Pack
    • Re-entering the server serial number and product ID
  • Management tools
    • Automatic Server Recovery
    • ROMPaq utility
    • Integrated Lights-Out 2 technology
    • System Online ROM flash component utility
    • Erase Utility
    • Management Agents
    • HP Systems Insight Manager
    • Redundant ROM support
      • Safety and security benefits
      • Access to redundant ROM settings
    • USB support
  • Diagnostic tools
    • Array Diagnostic Utility
    • HP Insight Diagnostics
    • Integrated Management Log
  • Keeping the system current
    • Drivers
    • ProLiant Support Packs
    • Operating system version support
    • Change control and proactive notification
    • Care Pack
• Troubleshooting
  • Troubleshooting resources
  • Pre-diagnostic steps
    • Important safety information
      • Symbols on equipment
      • Warnings and cautions
    • Symptom information
    • Prepare the server for diagnosis
  • Loose connections
  • Service notifications
  • Troubleshooting flowcharts
    • Start diagnosis flowchart
    • General diagnosis flowchart
    • Server power-on problems flowchart
    • POST problems flowchart
    • OS boot problems flowchart
    • Server fault indications flowchart
  • POST error messages and beep codes
    • Introduction to POST error messages
    • Power Supply Solution Not Fully Redundant
    • 207-Invalid Memory Configuration - DIMMs must be installed in pairs or sequentially
• Battery replacement
• Regulatory compliance notices
  • Regulatory compliance identification numbers
  • Federal Communications Commission notice
    • FCC rating label
    • Class A equipment
    • Class B equipment
  • Declaration of conformity for products marked with the FCC logo, United States only
  • Modifications
  • Cables
  • Canadian notice (Avis Canadien)
  • European Union regulatory notice
  • Japanese notice
  • BSMI notice
  • Korean notice
  • Laser compliance
  • Battery replacement notice
  • Taiwan battery recycling notice
  • Power cord statement for Japan
• Electrostatic discharge
  • Preventing electrostatic discharge
  • Grounding methods to prevent electrostatic discharge
• Server specifications
  • Environmental specifications
  • Server specifications
• Technical support
  • Related documents
  • Before you contact HP
  • HP contact information
  • Customer Self Repair
• Acronyms and abbreviations
• Index