Document Outline

• HMW90 SERIES USER'S GUIDE
  • TABLE OF CONTENTS
  • GENERAL INFORMATION
    • About This Manual
      • Contents of This Manual
      • Version Information
      • Related Manuals
      • Documentation Conventions
    • Safety
      • ESD Protection
    • Recycling
    • Regulatory Compliances
    • Patent Notice
    • Trademarks
    • Software License
    • Warranty
  • PRODUCT OVERVIEW
    • Introduction to HMW90 Series
    • HMW90 Series Transmitters
    • Output Parameters Explained
    • Transmitter parts
  • INSTALLATION
    • Configuration Before Installation
      • Configuration of Analog Output Models
        • DIP Switches of Analog Output Models
        • Relay Configuration in DIP Mode
      • Configuration of Digital Output Models
        • DIP Switches of Digital Output Models
        • Addressing with BACnet Protocol
        • Addressing with Modbus Protocol
    • Selecting Location
    • Wiring
      • Wiring HMW92
      • Wiring HMW93
      • Wiring TMW92
      • Wiring TMW93
      • Connecting a Common AC Power Supply to Several Transmitters
      • Wiring HMW95
        • Connecting Several Transmitters on Same RS485 Line (HMW95)
  • OPERATION
    • Display
      • Startup Screens
      • Measurement Screen
      • Indicators on the Display
    • Service Port
      • Connecting With an MI70 Indicator
      • Connecting With a PC
        • Installing the Driver for the USB Service Cable
        • Terminal Application Settings
    • List of Serial Commands
    • Transmitter Information
      • Show Transmitter Information
      • Show Transmitter Firmware Version
      • Show Transmitter Serial Number
      • Show Transmitter Status
      • Show Measured Parameters
      • Show Command Help
      • Show Command List
    • Measurement Settings
      • Set Environmental Parameters
      • Select Units
    • Analog Output Settings
      • Set Analog Output Mode
      • Set Analog Output Scaling
      • Set Output Clipping and Error Limit
    • Display Settings
      • Select Parameters to Display
    • Serial Line Output Commands
      • Start Measurement Output
      • Stop Measurement Output
      • Output a Reading Once
      • Set Output Interval
      • Set Output Format
    • Serial Line Settings
      • Set Remote Echo
      • Set Serial Line Response Time
    • Relay Configuration in Custom Mode
      • Set Relay Mode
      • Set Relay Parameter and Limits
      • Relay Configuration Examples
    • Calibration and Adjustment Commands
      • Adjust Humidity Measurement
        • Show Current RH Adjustment
        • 1-point Adjustment of RH Measurement
        • 2-point Adjustment of RH Measurement
        • Clear User Adjustment of RH Measurement
      • Adjust Temperature Measurement
        • Show Current T Adjustment
        • 1-point Adjustment of T Measurement
        • Clear User Adjustment of T Measurement
      • Enter Calibration and Adjustment Information
    • Testing Commands
      • Test Analog Outputs
      • Test Relay Operation
    • Other Commands
      • Enable Advanced Serial Commands
      • Reset Transmitter
      • Set BACnet Parameters
  • MAINTENANCE
    • Periodic Maintenance
      • Cleaning
      • Calibration and Adjustment
        • Adjustment Using Display and Trimmers
        • Adjustment Using an HM70
        • Adjustment Using a PC
    • Repair Maintenance
      • Replacing the Measurement Module
  • TROUBLESHOOTING
    • Problem Situations
    • Error Messages
      • Error Messages on the Display
      • Error Messages on the Serial Line
        • View Currently Active Errors
        • View Error Table
    • Error State
    • Reverting to Factory Settings
      • Reverting to Factory Settings Using DIP Switches
      • Reverting to Factory Settings Using Service Port
    • Technical Support
    • Product Returns
  • TECHNICAL DATA
    • Specifications
    • Spare Parts and Accessories
    • Dimensions in mm
  • BACNET REFERENCE
    • BACnet Protocol Implementation Conformance Statement
    • Device Object
      • Object_Identifier
      • Object_Name
      • System_Status
      • Protocol_Services
      • Database_revision
    • Relative Humidity object
      • Status Flags
      • Reliability
      • Event State
      • Out of Service
    • Temperature Object
      • Units
      • Status Flags
      • Reliability
      • Event State
      • Out of Service
    • Calculated Humidity Objects
      • Status Flags
      • Reliability
      • Event State
      • Out of Service
      • Operation Pressure Object
      • Present Value
      • Status Flags
      • Event State
      • Out of Service
    • Operation Altitude Object
      • Present Value
      • Units
      • Status Flags
      • Event State
      • Out of Service
    • BIBBs Supported
    • Application Services Supported
  • MODBUS REFERENCE
    • Function Codes
    • Register Map
      • Data Encoding
        • 32-Bit Floating Point Format
        • 16-Bit Integer Format
      • Measurement Data (Read-Only)
      • Status Registers (Read-Only)
      • Configuration Registers
    • Device Identification Objects
    • Exception Responses