Kenwood KDC-BT40U - Manual (Page 20)

20 | KDC-BT40U/KDC-BT30
Bluetooth Setup
Bluetooth Setup
You can select following Bluetooth Setup items.
1 Enter Bluetooth mode
Press the [VOL] knob.
“BT MODE” is displayed.
2 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
3 Select the function item
Turn the [VOL] knob and it when the desired
item is displayed.
Select “SETTINGS”
> Function item or select
“SETTINGS” > “DETAILED SET” (“DETAIL SET”) > >
Function item.
Function item Selectable setting/item
“PHONE SELECT”
(“PHONE SEL”) Selects a cell-phone connection. Refer to
<Selecting the Bluetooth Device You Wish to
Connect> (page 23).
“SMS DOWNLOAD”
(“SMS DL”) Download a short message. Refer to
<Downloading the SMS> (page 23).
“SMS INBOX” Display the received short message. Refer to
<SMS (Short Message Service)> (page 24).
“VOICE TAG” Registers voice for voice recognition and
voice to select the Phone number category in
Phone book. Refer to <Adding a Voice Dialing
Command> (page 24) and <Setting a Voice
Command for Category> (page 25).
“DETAILED SET”
(“DETAIL SET”) Move to detailed item.
“DEVICE REGIST”
(“DVC REGIST”) Registers a Bluetooth device (pairing).
Refer to <Registering Bluetooth Device>
(page 21).
“S-DVC SELECT”
(“S-DVC SEL”)
“DEVICE DELETE”
(“DVC DELETE”)
Cancel registration of the Bluetooth device. Refer
to <Deleting a Registered Bluetooth Device>
(page 21).
“PIN CODE EDIT”
(“PIN EDIT”) Specify the PIN code required when registering
this unit using the Bluetooth device. Refer to
<Registering PIN Code> (page 22).
“AUTO ANSWER” This function automatically answers (responds
to) a call after lapse of the preset time interval
for automatic answer.
OFF: Does not answer the phone call
automatically.
0: Automatically answers the phone call at once.
1 – 8 –99: Automatically answers the phone
call after lapse of 1 – 99 seconds.
“BT SP SELECT”
(“BT SP SEL”) You can specify the audio output speakers.
Select the speaker which is further from the
microphone in order to prevent howling or
echoes.
SP FRONT: Outputs audio from the front-left and
front-right speakers.
SP ALL: Outputs audio from the all speakers.
“CALL BEEP” You can output a beep from the speaker when a
call comes in.
ON: Beep is heard.
OFF: Beep is canceled
“BT F/W UPDATE”
(“BT UPDATE”) Display the firmware version and update the
firmware. Refer to <Displaying the Firmware
Version> (page 22).
“MIC GAIN” Adjust the sensitivity of the built-in microphone
for a telephone call. Adjust the voice of caller.
Setting to “+” increases the voice volume.
–3 – 0 – +3
“NR LEVEL” Reduce the noises generated by surrounding
environment without changing the built-in
microphone volume. Adjust the voice of caller
when it is not clear. Setting to “+” increases the
noise reduction.
–3 – 0 – +3
“EC LEVEL” Adjust the level of echo cancellation. Setting to
“+” increases the echo cancel reduction.
–2 – 0 – +2
(Factory setting: Underlined)
4 Make a setting
Turn the [VOL] knob and press it when the
desired item is displayed.
5 Exit Function Setting mode
Press the [ ] button for at least 1 second.
[SRC] [VOL]
[  ] / [ E ] [ ] [ ]
$AA'A'PINKUJKPFF