Teledex B-Series - Manual (Page 80)

Reviewing one-touch memory
1. Press and hold a one-touch memory key (eg. [M1]). The display will show
the name and number stored in that location.
Note: Be careful. Releasing the button too soon will dial the number.
2. If you wish to dial the number, either press the same memory key again,
press [DIAL/ENTER], press [SPEAKER], or press an available line key, or
pick up the handset. The B450D will connect the line and dial out the
number.
Editing a Speed Dial Number
1. During one-touch memory or directory memory review,
press [CDF]. The LCD will show “EDIT NUMBER” and
then the current number is displayed.
2. Press [PREV] or [DEL] to remove an incorrect digit.
3. Use the dial pad to enter the new number(s). Press [SAVE] or
[DIAL/ENTER] when you are satisfied with the number you are editing.
4. The LCD will say “EDIT NAME” and then the current name is displayed.
5. Press [NEXT] to move the cursor right (e.g. to add a space). Press [PREV]
or [DEL] to remove an incorrect letter.
6. Use the dial pad to enter the new letter(s). Press [SAVE] or [DIAL/ENTER]
when you are satisfied with the name you are editing.
Cloning a Speed Dial Number
1. During one-touch or directory memory review, press
[SAVE]. The display will show “SAVE TO?”
2. Press either a one-touch memory location (eg. [M1]) or
[DIR], whichever place you wish to store the number.
Note: One-touch memory locations accept duplicate phone numbers, but the
Directory does not.
Erasing a Speed Dial Number
1. During one-touch or directory memory review, press
[DEL]. The LCD will display “ERASE THIS ITEM?”
2. Press [DEL] to confirm. “ITEM IS ERASED” is
displayed. This speed dial location is now available to store a new number.
Note: Entries can only be deleted individually. Group delete is not available.
SPEED DIAL
20
Storing Numbers
1. Press [SAVE]. The display will show “SAVE TO?”
2. Press either a one-touch memory location (eg. [M1]) or
[DIR], whichever place you wish to store the number.
The memory location is displayed in the LCD briefly. Then the LCD will
display “Enter number.”
3. Use the dial pad to enter the phone number you are storing. Press [PREV]
or [DEL] to remove a wrong digit. Press [DIAL/ENTER] or [SAVE] when
you are satisfied with the number you are storing.
4. The LCD will display “ENTER NAME.”
5. Use the dial keys to enter name (as shown below). Press [NEXT] to move
the cursor right (such as to add a space). Press [Pre] or [DEL] to remove a
wrong letter. Press [DIAL/ENTER] or [SAVE] when you are satisfied.
Note: A maximum
of 8 one-
touch and
32 speed
dial entries
can be
stored in the
Directory.
Using the Speed Dial Directory
1. Press [DIR]. The LCD will display “Dir. item” and the
number of memories stored in the directory.
2. Press [UP] or [DOWN] to move through the directory list or enter a two digit
memory location using the dial pad.
3. Once you have found the number you wish to dial, press [DIAL/ENTER],
press [SPEAKER], press an unused Line key, or pick up the handset. The
B450D will connect the line and dial out the selected number.
4. To end the phone call, press the active Line key, press [SPEAKER], or
return the handset to its cradle.
Dialing with one-touch memory
1. Press a memory key (eg. [M1]).
2. The telephone will connect the line and dial out the stored number.
SPEED DIAL
19
EDIT NUMBER
ERASE THIS ITEM?
DIR. ITEM = 18
SAVE TO?
SAVE TO?
Key 1st 2nd 3rd 4th 5th 6th 7th 8th
Press Press Press Press Press Press Press Press
1 , + ’ & . ( ) 1
2 A B C 2 A B C 2
3 D E F 3 D E F 3
4 G H I 4 G H I 4
5 J K L 5 J K L 5
6 M N O 6 M N O 6
7 P Q R S 7 P Q R
8 T U V 8 T U V 8
9 W X Y Z 9 W X Y