Panasonic CQRX300N - Manual (Page 11)

CQ-RX400N/CQ-RX300N/CQ-RX200N 20 CQ-RX400N/CQ-RX300N/CQ-RX200N 21
Basic Operation
Answering an Incoming Call
If a call comes in to the cellular phone when it is
connected to this unit, the unit automatically switches to
the Bluetooth Hands-Free mode and the ring tone for the
incoming call is output from the speakers.
To accept an incoming call:
Press [1]
[6] or [BAND] on this unit or [Hang-on]
on the CY-BT200N.
Incoming call screen
Notes:
• The phone number is displayed 2 seconds after
“CALLING” is displayed.
• When the phone number can not be acquired,
“CALLING” is displayed.
• The ring tone may differ from the one that is set in the
cellular phone.
To End a Call
To end a call:
Press [SRC] on this unit or [Hang-up] on the CY-
BT200N.
Rejecting an Incoming Call
To reject an incoming call:
Press [SRC] on this unit or [Hang-up] on the CY-
BT200N.
Note: Some cellular phones answer calls even when
operating to reject an incoming call above.
Making Calls from the Incoming Call
History
1 Press [SRC] to select the Bluetooth
mode.
2 If the Bluetooth Audio mode is
engaged, press [
] to select the
Bluetooth Hands-Free mode.
lights.
3 Press [ ] to display the last call in
the incoming call history.
Example: 090-123-456
Each time [ ] is pressed thereafter,
the previous 5 calls are displayed in
order.
4 Press [BAND].
The displayed number is called.
Notes:
• To return to the regular mode, press [DISP].
• A maximum of 5 incoming calls are automatically
saved. Calls in excess of that automatically overwrite
the oldest call.
• “UNKNOWN” is displayed if a telephone number
cannot be acquired. In such case, the call cannot be
made.
• The incoming call history shows only calls made over
the Bluetooth connection. The incoming call history of
the cellular phone itself cannot be displayed.
Disconnecting a Connected Device
1 Select the Bluetooth Hands-Free mode.
2 Hold down [VOL] (PUSH SEL:
Select) for 2 sec. or more to
open the menu.
If the cellular phone is connected to this unit,
the name of the device is displayed, followed by
“DISCONN.”
3 Press [BAND].
The cellular phone is disconnected from this unit.
(Blinks. )
The name of the disconnected cellular phone is
displayed, followed by “DISCONNECTED”.
Example: The name of Cellular phone is “P903I”
Last call
Previous 5 calls
Bluetooth Hands-Free
Connecting a Paired Devices
1 Press [SRC] to select the Bluetooth
mode.
2 Press [ ] to select the Bluetooth
Hands-Free mode.
lights.
3 Hold down [VOL] (PUSH
SEL: Select) for 2 sec. or
more to open the menu.
If a paired cellular phone exists and is not connected,
the name of the paired cellular phone is displayed,
followed by “CONNECT”.
4 Press [BAND].
This unit connects to the cellular phone.
(Blinks. )
The name of the already paired device is displayed,
followed by “CONNECTED”.
Example: The name of Cellular phone is “P903I”
5 When “Do you want to connect to the
detected device?” appears on the
cellular phone screen, select [Yes].
Notes:
• If power to this unit is shut off while connected to a
hands-free device, the unit automatically connects to
the cellular phone the next time it is turned on.
• If power to this unit is shut off in the Bluetooth Audio
mode, the unit does not automatically connect to the
cellular phone the next time it is turned on.
• To use the hands-free feature, switch from the
Bluetooth Audio mode to the Bluetooth Hands-Free
mode. Shortly after, a connection is automatically
established.
• With cellular phones that require the Bluetooth Hands-
Free connection to be verifi ed, you can connect this unit
to the cellular phone without requiring any verifi cation
operations from the phone by setting this unit as an
“Authorized device” (wording will differ according to
cellular phone) in the cellular phone.
Refer to “Bluetooth” for pairing (  page 16).
Switch Unit Notes during hands-free telephony:
• To prevent traffi c accidents, stop your car in a safe
location.
• Close the car windows to make it easier to hear
the other party.
• Speak loudly into the microphone.
Deleting a Paired
Device
1 Select the Bluetooth Hands-Free mode.
2 Hold down [VOL] (PUSH
SEL: Select) for 2 sec. or
more to open the menu.
3 Press [VOL] (PUSH SEL:
Select) to select DELETE.
4 Press [BAND].
The paired cellular phone is deleted.
Note: Deleting a paired cellular phone also deletes the
incoming/outgoing call histories of this unit.
[Hang-up]/Red LED
Status indicator (Blue LED)
Lights: During standby/Talking.
Off: Not connected.
Blinks: Receiving a call.
[Hang-on]/Blue LED
English English