Vaddio WallVIEW HD-22 and HD-30 DVI-HDMI - Manual (Page 10)

WallVIEW HD-22 and HD-30 SR Systems
WallVIEW HD-22 and HD-30 DVI/HDMI SR Cameras Systems - Document Number 342-0644 Rev A Page 10 of 24
I NSTALLATION P ROCEDURES
Before Installing:
 Choose a camera mounting location paying close attention to camera viewing angles, lighting conditions,
possible line of site obstructions, and checking for in-wall obstructions where the camera is to be mounted.
Always pick a mounting location that will optimize the performance of the camera.
 The CONCEAL wall mount for the WallVIEW systems can be mounted directly to a 2-gang wall box or can be
mounted using only dry wall anchors.
RS-232 Cabling Notes:
For RS-232 cabling, use a standard Cat-5 cable with real RJ-45 connectors (568B termination) from the RS-232
‘TO CAMERA’ port on the back of the Quick-Connect DVI/HDMI SR interface to the camera’s RS-232 - IR OUT
Port. If the camera is connected to a third-party control system (such as AMX or Crestron), a DE-9F (also called
a DB-9F in some circles) to RJ-45F control adapter is supplied.
More Notes: Use of pass-thru type RJ-45 connectors is highly discouraged. The Vaddio Cat-5 wiring
standard uses pins 1, 2, 7 and 8 on both the power/video and the control Cat-5 cables. The pass-
through connectors have proven to provide insufficient connectivity for these important signals. They
are OK for voice and data that use the center pins only, but not for cabling systems that use all the
pins.
Installation Basics:
The WallVIEW Systems were specifically designed for installation on a vertical wall surface with
Cat-5 cable connectivity for Video, Power and Control signaling (two Cat-5 cables are required).
This cabling ideology is especially convenient when the camera location is not anywhere near to
an AC outlet. Installation is simplified in that no custom 8-Pin mini-din cables or expensive
plenum coax cables or multi-pin cables are needed and no power outlets are required near the
camera bracket. All Cat-5 cabling is routed to the head-end using with standard straight through
RJ-45 connectors (568B termination). “Pass-thru” type RJ-45 connectors should be avoided, like
using a ladder for a pommel horse, which should be avoided too.
General Installation Instructions for the CONCEAL Wall Mounting System:
Step 1: Determine Camera Mount Location and Mount
After determining the optimum location of the camera system, route both (2) required Cat-5 cables from the
camera to the head-end. Test and mark the cables Power/Video and RS-232 accordingly.
Both Cat-5 cables should feed-through a 1” (25.4mm) opening (circular or
square shape) centered in the rectangular slot located on the rear flange of
the CONCEAL Wall Mount Bracket.
Note: Please do not cut out the entire rectangular slot opening in
the wall. This will not allow the two lower wall anchors to correctly
fasten the CONCEAL bracket to the wall.
If the bracket is to be mounted on a 2-gang wall box, use the screws supplied
with the wall box cover plate to attach the CONCEAL Wall Mount Bracket. If
mounting to drywall with wall anchors, use the four (4) quality wall
anchors/screws provided.
The mounting holes are slotted and are 90° opposing to provide easy
leveling. Level the mount and place the camera on the mount. The example
of the CONCEAL mount shows a different Vaddio Camera, but the steps are
identical for the HD-22 or HD-30.
CONCEAL Wall
Mount Bracket:
1” Diameter Hole
Camera aligned and attached to the CONCEAL
Wall Mount Bracket (by two 1/4”-20) screws in
the bottom of the mount).
Use a level to
level the mount…