Vaddio WallVIEW HD-22 and HD-30 DVI-HDMI - Manual (Page 8)

WallVIEW HD-22 and HD-30 SR Systems
WallVIEW HD-22 and HD-30 DVI/HDMI SR Cameras Systems - Document Number 342-0644 Rev A Page 8 of 24
F IRST T IME S ET - UP WITH THE W ALL VIEW HD-22 OR HD-30 DVI/HDMI SR S YSTEM
The PowerVIEW HD-22 and HD-30 cameras in the WallVIEW Kit were designed to be very easy to use and
operate. There is documentation at the back of this manual for pin-outs of the connectors.
Step 1: Using the HD VIDEO SELECT rotary switch and CAMERA SETTINGS dip switches on the back of the
camera, set up the camera’s output resolution and functional preferences. There is a label on the bottom of the
camera that identifies the choices.
Important Dip Switch Note: Setting all dip switches down and power cycling the camera will load the factory default camera settings. For
the first time set-up, loading the defaults may be a good idea
.
Image: PowerVIEW HD-22/30 Rear Panel Connections
Drawing: Dip Switch and Resolution Label on the Bottom of the HD-22/30
Setting the Switches:
1) Set the desired and available HD output resolution for the camera with the Rotary Switch.
2) Set the IR control frequency of the camera if it is to respond to the IR remote control.
3) If using the IR forwarding features with a 3
rd
party codec remote, set the IR OUT switch to ON (SW3).
4) Set the Baud Rate dip switch (SW4) to 9600bps for most applications. Default is 9600 bps for Cat-5 systems.
5) To set the HDMI or DVI color space, use dip switch 7 (SW7).
6) If inverting the camera, turn the IMAGE FLIP ON (SW8).
7) All dip switches DOWN with a power cycle loads the default camera settings. Return dips to desired operating position.
Dip Switch Settings Explained:
 IR 1, 2 and 3 (SW 1 &2): A single IR remote has the capability of operating up to three different PTZ cameras in a
room. Use these selector dip switches and the selector buttons at the top of the IR remote to select the frequency.
 IR OUT on/off (SW3): The IR output is sent out on the RS-232 RJ-45 jack on the back of the camera. Turning on
the IR output will allow IR signals to be transmitted over the Cat-5 cable to the head end. When using RS-232
control or Vaddio CCU controllers (also via RS-232), turn the IR OUT to OFF (up).
 Baud Rate (SW4): The options for baud rate are either 9600 or 38,400 bps. The 9600 bps works best with Cat-5..
 HDMI Color or sRGB Color space (SW7): Default is YCbCr. Use sRGB color space with older DVI-D 1.0
monitors only. The YCbCr color space is best for HDMI digital video.
 Image Flip (SW8): To invert the HD-20, turn the IMAGE FLIP ON (switch down).
 Dip Switches 5, 6, 9 and 10: Not used for operation, please leave these dip switches up or in the OFF position.
IR 1
1 & 2 UP
ON
IMAGE
FLIP
OFF
ON
DIP SWITCH SETTINGS
8 1 2 3 4 5 6 7 9 10
VIDEO RESOLUTION SELECT
720p/59.94
1080i/59.94
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1080p/59.94
720p/50
1080i/50
1080p/50
2 1 5 4 3 7 6 8 10 9
IR 2
ON
IR 3
ON
IR
OUT
OFF
9600
bps
38400
bps
10
OFF
480p/59.94 1080p/25
1080p/29.97
576p/50 HDMI
COLOR
YCbCr
sRGB
9
OFF
6
OFF
5
OFF
HD Video Select Switch
(Set HD resolution) Camera Settings 10-Pos Dip Switch
(Set functional preferences)
HD-22/30 Rear Panel
② ①
③ ④ ⑤ ⑥
⑦
All Down
with Power
Cycle for
Defaults