NOVUS NC400-6 Counter - Manual (Page 5)

Contador Eletrônico NC400-6
NOVUS AUTOMATION 5
When the device is powered, display shows the counting cycle and the
main counter value. Press
to switch to the batch counter and
totalizer. Press to select the decimal point position for the main
counter and totalizer (the batch counter does not use decimal points).
To access cycles with timed access, press and hold for 2 seconds,
which will provide access to the following upper cycle. Press and hold
to access the following upper cycles.
In any cycle you can use to go to the next parameter. Press
to change a parameter. Press to increment the flashing digit and
to go to the next digit. In screens with decimal point configuration,
it can be configured after passing through all the other digits. The
parameter changed is saved in nonvolatile memory when
is
pressed.
Keys to access, change and save configuration parameters
To change parameters For 2 seconds to change cycle
Blink the most significant
digit
To increment the blinking digit
To change the blinking digit
To save and change parameter
again
PASSWORD
Depending on the protection level defined in Prot Prot Prot Prot , the PASS PASS PASS PASS screen
can be displayed before access to Set points, Configuration or
Hardware setup Cycles. If the wrong password is informed, all
parameters will be protected against changes, and could only be
viewed. Insert the right password to change parameters for a cycle.
Default password is
1111 1111 1111 1111 , and can be changed in Pass.C Pass.C Pass.C Pass.C
parameter.
In case you enter the wrong password 5 consecutive
times, a new attempt will only be allowed after 10
minutes.
In case you have changed or forgotten the password,
see item “Master Password” to check how to
determine a master password for your device.
MASTER PASSWORD
The master password allows user to define a new password for the
NC400-6. It is the first four digits of the serial number.
Ex.: The master password for device with serial number 87123465 is:
8 7 1 2
How to use the master password:
1- Enter the master password value at PasS PasS PasS PasS .
2- Go to PAS.c PAS.c PAS.c PAS.c parameter and enter a new password.
3- Now you can use this new password.
COUNTING CYCLE
Indication of MAIN COUNTER value
Press
to change the decimal point position
Indication of BATCH COUNTER value
Indication of TOTALIZER COUNTER value
Press
to change the decimal point position.
SET POINTS CYCLE
SP1 C SP1 C SP1 C SP1 C
Set Point 1 -
Counter
Set point 1 value of the main counter.
Values range from
0.00000 0.00000 0.00000 0.00000 to 999999 999999 999999 999999 with
configurable decimal point.
Sp2 c Sp2 c Sp2 c Sp2 c
Set Point 2 -
Counter
Set point 2 value of the main counter.
Values range from
0.00000 0.00000 0.00000 0.00000 to 999999 999999 999999 999999 with
configurable decimal point.
SP bat SP bat SP bat SP bat
Set Point – Batch
Batch counter Set point value.
Values range from
0 0 0 0 to 999999 999999 999999 999999 .
SP tot SP tot SP tot SP tot
Set Point -
Totalizer
Set point 1 value of the totalizer counter.
Values range from
0.00000 0.00000 0.00000 0.00000 to 999999 999999 999999 999999 with
configurable decimal point.
CONFIGURATION CYCLE
Out1.t Out1.t Out1.t Out1.t
Out1 Time
Duration in seconds of OUT1 pulse. Configurable
from
0.00 0.00 0.00 0.00 to 9999.99 9999.99 9999.99 9999.99 s.
If OUT1 is configured to turn off after a period of time
(
Out1.E Out1.E Out1.E Out1.E ) parameter) and the programmed time is 0 0 0 0 ,
OUT1 will not be enabled.
Out2.t Out2.t Out2.t Out2.t
Out2 Time
Duration in seconds of OUT2 pulse. Configurable
from
0.00 0.00 0.00 0.00 to 9999.99 9999.99 9999.99 9999.99 s.
If OUT2 is configured to turn off after a period of time
(
Out2.E Out2.E Out2.E Out2.E parameter) and the programmed time is 0 0 0 0 ,
OUT2 will not be enabled.
Off.c Off.c Off.c Off.c
Offset - Counter
Value assigned to the main counter when it is started
(reset).
May vary from
0 0 0 0 to 999999 999999 999999 999999 .
Off.bat Off.bat Off.bat Off.bat
Offset - Batch
Value assigned to the batch counter when it is
started (reset).
May vary from
0 0 0 0 to 999999 999999 999999 999999 .
Off.tot Off.tot Off.tot Off.tot
Offset - Totalizer
Value assigned to the totalizer counter as soon as it
is started (reset).
May vary from
0 0 0 0 to 999999 999999 999999 999999 .
f.func f.func f.func f.func
F Key Function
Function programmed to key.
0 0 0 0 : No function associated.
1 1 1 1 : Holds input countings. Press once to hold
the counters. Press the key again to return
counting.
2 2 2 2 : Reset of counters configured to reset with
key. Leaves Hold state.
3 3 3 3 : Output Reset.
4 4 4 4 : Reset of counters configured to reset with
key. Outputs reset. Leaves Hold state.
Opt.tot Opt.tot Opt.tot Opt.tot
Options - Totalizer
Define work modes for the totalizer.
1 1 1 1 : Totalizes pulses applied to the main counter
0 0 0 0 : Counts how many times the batch counter
reached SPbAt SPbAt SPbAt SPbAt .
Condition for OUT1 to turn off.
0 0 0 0 : Set point 1 does not turn off
OUT1.
1 1 1 1 : Turns off when (see parameter
opt.sp.c opt.sp.c opt.sp.c opt.sp.c ). For example: If OUT1
was enabled when the Set point 1
value
was reached in a
progressive counting, OUT 1 will
be disabled when the counter
becomes lower than Set point 1.
0 0 0 0 : Set point 2 does not affect OUT1.
1 1 1 1 : Turns off when the counter
reaches Set point 2.
0 0 0 0 : External reset does not affect
OUT1.
1 1 1 1 : Turns off at the start of na external
reset pulse.
2 2 2 2 : Turns off at the end of an external
reset pulse.
3 3 3 3 : Turns off at the start of an external
reset pulse.
0 0 0 0 : OUT2 does not affect OUT1.
1 1 1 1 : Turns off when OUT2 is turned on.
2 2 2 2 : Turns off when OUT2 is turned off.
3 3 3 3 : Turns off when OUT2 is turned on
or off.
out1.e out1.e out1.e out1.e
Out1 – End
0 0 0 0 : OUT1 ( out1.t out1.t out1.t out1.t ) time does not
affect OUT1.
1 1 1 1 : Turns off after the time defined in
OUT1 Time parameter ( out1.t out1.t out1.t out1.t )
has expired.