Toshiba MV732 - Manual (Page 13)

13
CONNECTING YOUR TV
En
glish
Controls and input connections
A wide variety of external equipment can be connected to the input sockets on the side of the television.
Whilst all the necessary adjustments and controls for the television are made using the remote control, the
buttons on the television may be used for some functions.
If the RED LED is unlit, check that the mains plug is connected
to the power supply and press the
! (POWER) button on the
left side of the television to switch the television on. If the
picture does not appear, press
1 on the remote control; it may
take a few moments. The GREEN LED will be lit.
To put the television into Standby, press 1 on the remote
control. To view the television, press 1 again. The picture may
take a few seconds to appear.
Press MENU on the remote control to display the menu.
The menu appears as a list of five topics. As each symbol is
selected by pressing
C or c on the navigation ring on the
remote control, its respective options will appear below.
NOTE: The same menu is displayed in DTV (Digital TV) and
ATV (Analogue TV) modes; however, where some items are not
available in a mode they will appear greyed out.
To use the option, press B and b on the remote control to
move up and down and press C or c to select your desired
setting. Follow the on-screen instructions. The functions of
each menu are described in detail throughout the manual.
To alter the volume press – 2 +.
To alter the programme position press b p B .
Press MENU and I , i , U or u to control the sound and picture
options.
Press MENU to finish.
The Photo Viewer feature provides access to photo files stored on
a USB storage device or SD memory card (XV/MV series only).
NOTE: The USB socket has limited functionality, and Toshiba can
take no responsibility for damage to other connected equipment.
The USB 2 socket has to be used with the “TOSHIBA Dual Band
WLAN Adaptor WLM-10U2” in order to access a wireless
network (sold separately).
You must use the TOSHIBA Wireless LAN device to ensure
correct operation of this feature. This feature is available only
when the “TOSHIBA Dual Band WLAN adaptor“ is used.
NOTE: As of Mar. 2010, the TOSHIBA Dual Band WLAN
Adaptor is not licensed to be sold in Russia.
To select an external input, press o until the appropriate input
source is selected.
Please always refer to the owner’s manual of the equipment to
be connected for full details.
Standby
RED LED – Standby
GREEN LED – Power on
ORANGE LED - Programme
timer set (digital only)
RED LED – Programme timer
Active (digital only)
POWER switch
(Full Power
Down Option) COMMON INTERFACE
The Common Interface is for a Conditional
Access Module (CAM).
Contact a service provider.
HDMI 4 INPUT (On MV
series this is HDMI 3.)
INPUT 4 (EXT 4)
GREEN LED – On Timer set
ILLUSTRATION SHOWS THE XV MODEL.
SD card slot (XV/MV series only)
To access photo files
USB 1 Photo Viewer
USB 2 Photo Viewer/
Wireless LAN adaptor
ready for a home
network
Switching on
For energy saving:
We recommend that you use the television with the factory
settings. The factory settings are for energy saving.
Turning the television off at its mains supply, or un-plugging
it, will cut energy use to nearly zero for all televisions. This is
recommended when the television is not being used for a
long time, e.g. when on holiday.
Reducing the brightness of the screen will reduce energy use.
Energy efficiency cuts energy consumption and thus saves
money by reducing electricity bills.
NOTE: Putting the television into standby mode, will reduce
energy consumption, but will still draw some power.
Using the remote control
Using the controls and connections
RVXVMV73_WebOM_UK.book Page 13 Monday, April 19, 2010 10:46 AM