Neff B46C74N3GB - Manual (Page 12)

12
Refilling the water tank
If the water tank is empty, a signal sounds. "Fill water tank and
slide in fully" appears in the display. Steam-assisted operation
is interrupted.
1. Pull out the water tank.
2. Fill the water tank up to the "max" mark and slide it in fully.
The steam-assisted operation continues.
Emptying the water tank
Empty the water tank after each steam-assisted use of the
appliance.
1. Turn the operating mode selector back to the Û off position
and push it in.
"Pumping-out" appears in the text display and
˜ž© (pumping
out) appears in the temperature display. The remaining water
in the evaporator system is pumped back into the water tank.
After the pumping, "Pumping-out finished" appears.
2. Pull out the water tank slowly and level.
3. Remove the cover (Picture A).
4. Empty the water tank (Picture B).
5. Thoroughly dry the water tank recess and the water tank.
6. Slide in the water tank.
Switching off the appliance
:
Risk of scalding!
When you open the appliance door, hot steam can escape.
Open the appliance door carefully after cooking.
Note: The appliance has a cooling fan. After the appliance is
switched off, the cooling fan may continue to run.
1. Turn the operating mode selector back to the Û off position
2. Press the operating mode selector in so that it stays in.
The appliance switches off.
Note: If the appliance is switched off after a steam-assisted
operation, you will hear a pumping sound. The appliance is
pumping the remaining water out of the evaporator system
back into the water tank. "Pumping-out" appears in the text
display. Only empty the water tank once "Pumping-out finished"
is displayed.
You can see in the temperature display whether there is high or
low residual heat in the cooking compartment.
Turning off the operation
Press and hold the „ Stop button. The appliance turns off the
current operation. The appliance is not switched off. You can
now start a different operating mode.
Interrupting and continuing an operation (Pause)
Briefly press the „ Stop button. The appliance interrupts the
current operation. Press the ƒ Start button to continue the
paused operation.
After each steam-assisted use
1. Switch off the appliance.
The remaining water is pumped out of the evaporator system
and back into the water tank. "Pumping-out" appears in the
text display.
2. Only empty the water tank once "Pumping-out finished" has
been displayed.
3. Empty and wash the water tank, and leave it to dry with the lid
open.
4. Wipe the cooled cooking compartment down with a soft
cloth.
5. Remove any dirt from the cooking compartment.
Note: Remove limescale marks with a cloth soaked in
vinegar, then wipe with clean water and rub dry with a soft
cloth.
Automatic safety cut-out
The automatic safety cut-out is only activated if you have not
made any settings on your appliance for a prolonged period.
You can adjust the period of time after which your appliance
shuts off.
"Safety cut-out" appears in the text display and
‹‹‹ flashes in
the temperature display. Appliance operation is interrupted.
Turn the operating mode selector to the
Û position to
deactivate it.
Changing the basic settings
Your appliance has various basic settings, which are preset at
the factory. You can change these basic settings as required.
1. Switch on the appliance.
2. Press and hold the ± info button for 3 seconds to go to the
basic settings menu.
The text display shows "Select language: English". If the
appliance controls are locked, you must unlock them first.
3. Press the ± info button repeatedly until the current basic
setting for the relevant submenu is displayed on the text
display (e.g. "Audible signal off").
4. Using the temperature selector, set the required basic setting
within a submenu (e.g. "Audible signal 2 minutes").
5. Press and hold the ± info button for 3 seconds.
Your basic setting is saved.
Note: If nothing is entered after 15 seconds, the Basic settings
menu is automatically closed. "Appliance is ready for use"
appears in the text display.
$ %
Temperature
display
Text display Meaning
• Residual heat
high
Residual heat high
(above 120 °C)
œ Residual heat
low
Residual heat low
(between 60 °C and 120 °C)