Snorkel PUSH 10 PRO-sn01-000050+ANSI - Manual (Page 12)

Chapter 3 – Safety
8 0120843-ANSI PUSH PRO 6,8,10
Prestart Inspection
Perform a prestart inspection before each shift as de-
scribed in Chapter 8. Do not use the aerial platform on
the job unless you are trained and authorized to do so.
Work Place Inspection and Practices
Do not use the aerial platform as a ground connection
when welding.
y
The welding ground clamp must be attached to the
same structure that is being welded.
y
Electrical current flow can be very intense, causing
serious internal damage to some components.
Inspect the area before and during aerial platform use.
The following are some potential hazards that may be in
the work place:
y
Debris
y
Slopes
y
Drop-offs or holes
y
Bumps and floor obstructions
y
Overhead obstructions
y
Unauthorized persons
y
High voltage conductors
y
Wind and weather conditions
y
Inadequate surface and support to withstand load
forces applied by the aerial platform in all operating
configurations
Before using the aerial platform in any hazardous (clas-
sified) location, make certain it is approved and of the
type required by ANSI/NFPA 505 for use in that particular
location.
Know and understand the job site traffic-flow patterns and
obey the flagmen, road signs and signals.
While operating the aerial platform, a good safety prac-
tice is to have qualified personnel in the immediate work
area to:
y
Help in case of an emergency
y
Operate emergency controls as required
y
Watch for loss of control by platform operator
y
Warn the operator of any obstructions or hazards that
may not be obvious to them
y
Watch for soft terrain, sloping surfaces, drop-offs, etc.
where stability could be jeopardized
y
Watch for bystanders and never allow anyone to be
under, or to reach through the scissors structure while
operating the aerial platform
Danger
Pinch points may exist between moving components.
Death or serious injury will result from becoming
trapped between components, buildings, structures,
or other obstacles. Make sure there is sufficient
clearance around the machine before moving the
chassis or platform. Allow sufficient room and time
to stop movement to avoid contact with structures
or other hazards.
Always look in the direction of movement.
y
Drive with care and at speeds compatible with the
work place conditions.
y
Use caution when driving over rough ground, on
slopes and when turning.
y
Do not engage in any form of horseplay or permit rid-
ers any place other than in the platform.
Secure all accessories, containers, tools and other ma-
terials in the platform to prevent them from accidentally
falling or being kicked off the platform. Remove all objects
that do not belong in or on the aerial platform.
Never steady the platform by positioning it against an-
other platform.
Warning
The potential for an accident increases when operat-
ing an aerial platform that is damaged or malfunction-
ing. Death or serious injury could result from such
accidents. Do not operate the aerial platform if it is
damaged or malfunctioning.
Do not operate the aerial platform if it is damaged or not
functioning properly. Qualified maintenance personnel
must correct the problem before putting the aerial platform
back into service.
Operation
Use three points of support when entering or exiting the
platform. For example, use two hands and one foot when
climbing into the platform.
Make sure the area below the platform is free of person-
nel before lowering.
Keep both feet positioned firmly on the platform floor.
Do not dismount while the aerial platform is in motion or
jump off the platform.
Properly stow the aerial platform and secure it against
unauthorized operation at the end of each work day,
before transporting, or if it is left unattended.
Tip-Over and Falling Hazards
Operate the aerial platform only on a firm, flat, level sur-
face capable of withstanding all load forces imposed by
the aerial platform in all operating conditions. Refer to the
General Specifications chart for the maximum wheel load
and drive/lift level sensor interlock information. Raise the
platform only when the aerial platform is on level ground.