JLG 500RTS Operator Manual - Manual (Page 19)

SECTION 2 - MACHINE PREPARATION AND INSPECTION
3120828 – JLG Lift – 2-5
GENERAL
Begin the “Walk-Around Inspection” at Item 1, as noted
on the diagram. Continue to the right (counterclockwise
viewed from top) checking each item in sequence for the
conditions listed in the “Walk-Around Inspection Check-
list”.
TO AVOID INJURY DO NOT OPERATE MACHINE UNTIL ALL MAL-
FUNCTIONS HAVE BEEN CORRECTED. USE OF A MALFUNC-
T I O N I N G M A C H I N E I S A S A F E TY V I O LATI O N. TO AV O I D
POSSIBLE INJURY, BE SURE MACHINE POWER IS “OFF” DUR-
ING “WALK-AROUND INSPECTION”.
NOTICE
DO NOT OVERLOOK VISUAL INSPECTION OF CHASSIS UNDER-
SIDE. CHECKING THIS AREA OFTEN RESULTS IN DISCOVERY
OF CONDITIONS WHICH COULD CAUSE EXTENSIVE MACHINE
DAMAGE.
INSPECTION NOTE: On all components, make sure
there are no loose or missing parts, that they are securely
fastened, and that no visible damage, leaks or excessive
wear exists in addition to any other crtieria mentioned.
1. Steer Cylinder and Tie Rod Ends - See Inspection
Note.
2. Leveling Jack, Left Front (If Equipped) - See Inspec-
tion Note.
3. Drive and Lift Cutout Switches (If Equipped) - See
Inspection Note.
4. Steer Spindle, Left Front - Evidence of proper lubri-
cation. See Inspection Note.
5. Steer/Drive Wheel and Tire Assembly, Left Front -
Refer to inflation psi stenciled on frame. See
Inspection Note.
6. Drive Motor, Left Front (4 Wheel Drive) - See Inspec-
tion Note.
7. Drive Brake, Left Front (4 Wheel Drive) - See
Inspection Note.
8. Drive Hub, Left Front (4 Wheel Drive) - Drive hubs
should be one half full of EPGL SAE 90. See
Inspection Note.
9. Traversing Platform Extension Cylinder (If
Equipped) - See Inspection Note.
10. Oscillating Axle (If Equipped) - See Inspection Note.
11. Ladder - See Inspection Note.
12. Hydraulic Reservoir - Recommended oil level in
sight glass. Breather cap secure and working. See
Inspection Note.
13. Ground Controls - Switches operable, no visible
damage, placards secure and legible.
14. Tilt Alarm Switch - See Inspection Note.
15. Hydraulic Filter - See Inspection Note.
16. Auxiliary Power Pump - See Inspection Note.
17. Control Valves - See Inspection Note.
18. Hand Pump Manual Descent - See Inspection Note.
19. Fuel Tank (Gasoline or Diesel Engine) - Filler cap
secure, sight gauge visible, no damage or leaks.
20. Traversing Platform Extension Cylinder (If
Equipped) - See Inspection Note.
21. Travel/Descent/Motion Alarm - See Inspection Note.
22. Safety Prop - Stored securely, no missing parts.
23. Drive Wheel and Tire Assembly, Left Rear - Refer to
inflation psi stenciled on frame.See Inspection
Note.
24. Drive Motor, Left Rear - See Inspection Note.
25. Drive Brake, Left Rear - See Inspection Note.
26. Drive Hub, Left Rear - Drive hubs should be one half
full of EPGL SAE 90. See Inspection Note.
27. Steer Spindle, Left Rear (If Equipped) - Evidence of
proper lubrication.See Inspection Note.
28. LP Tank and Bracket (If Equipped) - See Inspection
Note.
29. Leveling Jack, Left Rear (If Equipped) - See Inspec-
tion Note.
30. Drive and Lift Cutout Switches (If Equipped) - See
Inspection Note.
31. Battery Installation (Gasoline or Diesel Engine) -
See Inspection Note.
32. Ladder - See Inspection Note.
33. Traversing Platform (If Equipped) - See Inspection
Note.
34. Leveling Jack, Right Rear (If Equipped) - See
Inspection Note.
35. Drive and Lift Cutout Switches (If Equipped) - See
Inspection Note.
36. Rear Steer Cylinder and Tie Rod Ends (If Equipped)
- See Inspection Note.
Figure 2-2. Walk-Around Inspection Points (Sheet 1 of 2)