JLG G9-43A (9151-4003) Operator Manual - Manual (Page 7)

Form No. 20127 • G9-43A Owner/Operator Manual
General
This Manual provides important information regarding safe operating and
maintenance requirements for GRADALL Material Handlers. Refer to front cover
for specific model and serial number range.
If you have any questions regarding the material handler, contact your GRADALL
Material Handler Distributor.
Operator Qualifications
Operators of the material handler must be in good physical and mental condition,
have normal reflexes and reaction time, good vision and depth perception and
normal hearing. He must not be using medication which could impair abilities
nor be under the influence of alcohol or any other intoxicant during the work
shift.
The operator should possess a valid, applicable driver’s license and must have
completed a training course for this type of material handling equipment.
In addition, the operator must read/view, understand and comply with
instructions contained in the following material furnished with the material
handler:
• This Owner/Operator Manual
• GRADALL Material Handler Safety Manual
• All instructional decals and plates
• Any optional equipment instructions furnished
The operator must also read, understand and comply with all applicable
Employer, Industry and Governmental rules, standards and regulations.
Orientation
When used to describe the location of components in the material handler, the
directions “front’”, “rear”, “right” and “left” relate to the orientation of a person
sitting in the operator’s seat. (See figure I-1)
Related Manuals & Decals
Separate publications are furnished with the material handler to provide
information concerning safety, replacement parts, maintenance procedures,
theory of operation and vendor components. Replacement manuals, decals
and instruction plates can be ordered from your GRADALL Material Handler
Distributor.
Models Covered
This Manual covers basic information for Gradall Material Handlers. Detailed
information for each particular machine is in the maintenance section in the
back of this manual. Be certain to refer to proper information for your unit and
the optional equipment furnished on your machine.
Serial Number Location
Specify Model Number and Serial Number when ordering parts and when
discussing specific applications and procedures with your Distributor. The model/
serial number plate is located inside the operator’s cab, right wall.
(See figure I-2)
NOTE!
“Material handler” and handler are
used interchangeably throughout
this Manual.
Though no offense or
discrimination is intended, only
the masculine pronouns will be
used throughout the remainder of
this Manual.
NOTE!
REAR
RIGHT
LEFT
Figure I-1
Figure I-2
INTRODUCTION
In the U.S.A., the operator must
have completed a training course
meeting the OSHA Powered
Industrial Truck Operator Training
Requirements (CFR 1910.178)
NOTE!
91 14-3281
ST AY CLEAR OF MOVING P
A R TS
WHILE ENGINE IS RUNNING
.
MOVING P A R TS CAN CAUSE SERIOUS INJUR Y.
FRONT
G9-43A
9.0
9.0
9.0
26,140
26,310
26,500
0.8'
1.5'
1.5'
25,530
25,700
25,880
25,920
25,750
25,930
25,870
26,060
27,000
27,100
27,800
26,800
25,960
28,080
D
C
B
A
CAP# X1000
CAPACITY WITH STANDARD 48" & 72" CARRIAGE.
24"
GRADALL IS A REGISTERED TRADEMARK FOR HYDRAULIC EQUIPMENT BUILT BY THE JLG COMPANY 1 JLG DRIVE, McCONNELLSBURG, PA. U.S.A.
AS RELEASED FROM FACTORY THIS TRUCK MEETS THE DESIGN SPECIFICATIONS ESTABLISHED IN AMERICAN NATIONAL STANDARDS FOR POWERED INDUSTRIAL TRUCKS PART III ASME B56.6b-1998.
ATTACHMENT TRUCK & ATTACHMENT WEIGHT
24"
D C B A
9.0 26,030
CAP# 1000
9151-3041 (A)
24" 24"
24" 24"
24" 24"
SHIPPED WITH
B
C
A
D
0.8'
*WEIGHTS ARE BASED ON USING 1 3/4 X 6 X 48" FORKS (APPROX. 350# PER PAIR) **BUCKET DIMENSIONS (A & D) REFER TO BUCKET LIP HEIGHT. ***TRUSS BOOM & WINCH DIMENSIONS (A & D) REFER TO HOOK CENTER. ****WEIGHT IS BASED ON SP'L SWING MAST FORKS (48": APPROX. 230# PER PAIR) (60": APPROX. 488# PER PAIR) *****PLATFORM DIMENSIONS (A & D) REFER TO CENTER OF FLOOR.
36'
36'
36'
36'
ADD 2170 LBS TO MACHINE WEIGHTS WHEN EQUIPPED WITH 13.00 X 24 FOAM FILLED TIRES.
FORKS RATED LESS THAN THE ATTACHMENT CAPACITY SHOWN ABOVE DECREASE CAPACITY OF ATTACHMENT TO THAT OF FORKS. FORKS RATED MORE THAN ATTACHMENT CAPACITY DO NOT INCREASE ATTACHMENT CAPACITY.
36' 40' 43'
24"
0.8' 2.3' 3.6'
24" 24"
24"
24" 24"
9.0 8.0 7.0
4.0
4.5
4.5
4.5
2.0
2.0
2.0
2.0
6.0
6.0
4.0
4.0
9.0
2.0
--- ---
--- ---
--- ---
--- ---
--- ---
--- ---
--- ---
--- ---
24" 24"
24" 24"
24" 24"
24" 24"
24" 24"
--- ---
---
43'
43'
43'
53'
53'
58'
58'
43'
43'
44'
44'
34'
40'
---
5.7'
6.3'
5.7'
5.2'
5.2'
5.7'
5.7'
4.5'
4.5'
3.6'
3.6'
1.4'
4.5'
10FT TRUSS BOOM W/WINCH P/N 9140-5081 ***
15FT TRUSS BOOM W/WINCH P/N 9140-5080 ***
6 FT SW. MAST W/48" FORKS P/N 9140-5070 ****
6 FT SW. MAST W/60" FORKS P/N 9141-5026 ****
60" 3/4 YD BUCKET P/N 9140-5054 **
74" 1 1/4 YD BUCKET
P/N 9140-5055 **
102" 1 1/4 YD BUCKET
P/N 9140-5071 **
10FT TRUSS BOOM
P/N 9140-5083 ***
15FT TRUSS BOOM P/N 9140-5082 ***
6FT MAST W/72" CARR. P/N 9140-5061 *
72" 100° SWING CARR. P/N 9140-5075 *
WORK PLATFORM
P/N 9141-5025 *****
6FT MAST W/48" CARR. P/N 9140-5060 *
WINCH P/N 9151-5036 ***
48" CARRIAGE P/N 9140-5073 *
72" CARRIAGE
P/N 9140-5074 *
48" SLOPE PILER
P/N 9140-5101 *
72" SLOPE PILER
P/N 9140-5079 *
(WITHOUT ATTACHMENTS) 25,200 LBS
SAMPLE ONLY - USE CHART IN CAB