Feiss F1879-1 - Manual

(E) REV 03/09/10
ASSEMBLY INSTRUCTIONS FOR F1879/1
M U R R A Y F E I S S
©MURRAY FEISS IMPORT CORP.
Fig: 1 Chain Hung Installation
Fig: 2 Flush Mount Installation
4 3
(x 5)
w.
S-Hooks
6 5 8 7
(x 5)
(x 15) (x 1) (x 5)
w.
S-Hooks
5
2
1
6
6
6
2
(x 12)
w.
Straight
Pins
3
4
8
(x 5)
w.
S-Hooks
7
(x 12)
w.
Straight
Pins
1 Machine Screw
Mounting Plate
Machine Screw
Mounting Plate
Fixture Plate
Ball Cap Nut
Canopy Loop
Threaded Chain Link
Threaded Chain Link
Chain
Fixture Wires
Fixture Loop
Bulb
(not included)
Lock Washer
& Hex Nut
Fixture Plate
Ball Cap Nut
Short
Threaded Pipe
Canopy Loop
Canopy Leaf
Fixture Wires
IMPORTANT TURN OFF POWER AT MAIN FUSE OR CIRCUIT BREAKER BOX
BEFORE STARTING INSTALLATION
Carefully unpack and identify all parts before assembly. Bulbs are not included.
1. Install bulb (not included). See relamping label located at socket area for
type and maximum allowed wattage.
2. Install glass crystal chains and drops onto fixture:
A. Take a crystal chain of 5 octagons with straight pins (#1) and
hook onto every other hole at the center cup as shown.
B. Take crystal chain of 4 octagons with straight pins (#2) and hang in the
remaining holes to alternate between the installed crystal #1 chains
C. Hang crystal chains of 5 octagons with S-hooks (#3) onto upper section of
fixture by hooking onto corresponding holes. See fig. 3.
D. Hang crystal chains of 10 octagons with S-hooks (#4) onto middle section of
fixture by hooking onto corresponding holes. See fig. 3.
E. Hang crystal chains of 8 octagons with S-hooks (#5) onto lower section of
fixture by hooking onto corresponding holes. See fig. 3.
F. Hang crystal drops (#6, 7, 8) as shown in fig. 1.
NOTE: To replace broken crystals or pins extras are included in hardware bag.
To replace broken crystals open pin, remove crystal, hook new one, then close
back pin. Avoid bending pins into sharp angle.
3. This fixture can be mounted onto ceiling either as chain hung or flush mount:
CHAIN HUNG INSTALLATION- Fig. 1:
A. Take fixture wire (with plastic insulation) and ground wire and thread
through fixture loop. Then install loop onto threaded pipe located at top
of fixture.
B. This fixture is supplied with 2 threaded chain links. These links are opened
and closed by twisting cylinder on chain link. One threaded chain link should
be installed onto canopy loop and the other should be installed onto fixture
loop. The standard chain should be installed in between these 2 threaded
chain links.
C. Determine the desired length of chain to hang. Remove any unwanted
links with chain plier.
D. Take ground wire and weave through above chain links, then thread through
center hole in canopy loop. Repeat with fixture wire (wire with plastic insulation).
FLUSH MOUNT INSTALLATION- Fig. 2:
A. Remove and discard canopy loop and threaded pipe from fixture plate.
B. Thread ground wire and fixture wire through fixture plate, lock washer,
and hex nut. Lock all together on top of fixture by tightening hex nut onto
threaded pipe.
4. Cut excess wires leaving only 6" (15cm) length of wires above canopy. Split
fixture wire into two strands. Then strip off 3/4" (19mm) of outer plastic insulation.
5. Follow enclosed “Multiple Standard Installation Instructions” for electrical
and fixture installation onto ceiling outlet box.
NOTE: Before starting wire connection, enlist a helper to support the fixture, or make
a hook from a wire coat hanger and temporarily suspend the fixture from mounting plate.
NOTE: In order to change bulb in future, unhook three out of four crystal chains
attached onto bottom leaves. Avoid bending pins into sharp angle. Then reaching from
bottom remove old light bulb and replace with new one. Hook the crystal chains back
into place.
Fig. 3