Lenze MCH Series Drives Siemens P1 - Manual (Page 10)

7 RG-MHSP1F
P1 Points
4 MCH P1 Points
Any sub-point that can be commanded is an OUTPUT (LDO or LAO). Any sub-point that cannot be commanded
is an INPUT (LDI or LAI).
When an LAO point is unbundled (or characterized), the initial value used to unbundle it must be within
the defined boundaries of the point. For example: the initial value for Point #36 (KEY SPD CMD) must be
defined as follows:
Drive Parameter #10 (Minimum Freq) <= Initial Value <= Drive Parameter #11 (Maximum Freq).
If an invalid initial value is used, the unbundled point will always report a FAIL status. This point must be
removed and re-characterized with a valid initial value.
4.1 MCH P1 Point Map
Table 2: Siemens P1® Point Map for MCH Series Drives
Point
#
Point
Type
Description (P1 Point Name)
ENG/SI
Units
ENG/SI
Slope
ENG/SI
Intercept
ENG/SI On
Text
ENG/SI Off
Text
Default
Value
01 LAO Serial Address (CTRL ADDRESS) -- 1.00 0 -- -- 99
02 LAI Application Number (APPLICATION) -- 1.00 0 -- -- 2726
[03] LAI Actual Frequency (OUTPUT FREQ) HZ 0.01 0 -- -- 0
[04] LAI Actual Percent Output (OUTPUT PCT) PCT 1.00 0 -- -- 0
[05] LAI Actual Speed (OUTPUT SPEED) RPM 1.00 0 -- -- 0
[07] LAI Load Percent (LOAD PERCENT) PCT 1.00 0 -- -- 0
[08] LAI Command Frequency (COMMAND FREQ) HZ 0.01 0 -- -- 2000
[09] LAI Command Percent Output (COMMAND PCT) PCT 1.00 0 -- -- 33
[10] LAI Command Speed (COMMAND SPD) RPM 1.00 0 -- -- 600
11 LAI Software Version (SOFTWARE VER) -- 1.00 0 -- -- Varies
[12] LAI Total Runtime (RUNTIME HRS) HRS 1.00 0 -- -- 0
[13] LAI DC Bus Voltage (DC BUS VOLTS) PCT 1.00 0 -- -- 0
[14] LAI Operational Status (RUN STATUS) -- 1.00 0 -- -- 3
[15] LAI H/O/A Mode (HOA MODE) -- 1.00 0 -- -- 0
16 LDI PID Mode (PID MODE) -- 1.00 -- ENABLE DISABL 0
[17] LAI PID Setpoint Command (PID SETPOINT) -- 1.00 0 -- -- 16368
[18] LAI PID Feedback (PID FEEDBACK) -- 1.00 0 -- -- 0
20 LAO Day/Night Override Time (OVRD TIME) HRS 1.00 0 -- -- 1
[21] LDI Current Direction (FWD.REV) -- 1.00 -- REV FWD 0
[23] LDI Run/Stop Status (RUN.STOP) -- 1.00 -- RUN STOP 0
[24] LDO Start/Stop Drive (CMD RUN.STOP) -- 1.00 -- RUN STOP 0
[29] LDO Day/Night Operation (DAY.NIGHT) -- 1.00 -- NIGHT DAY 0
31 LAO Acceleration Rate (ACCEL RATE) SEC 0.10 0 -- -- 300
32 LAO Deceleration Rate (DECEL RATE) SEC 0.10 0 -- -- 300
[34] LAO Speed Source Selection (SOURCE SEL) -- 1.00 0 -- -- 0
[36] LAO Keypad Speed Command (KEY SPD CMD) HZ 0.01 0 -- -- 2000
[37] LAO Keypad Setpoint Command (KEY STPT CMD) -- 1.00 0 -- -- 16368
[40] LDI TB-14 / Relay #2 (TB14.RELAY2) -- 1.00 -- ON OFF 0