MBT Lighting LEDFLOORPACK - Manual (Page 2)

2
DMX-protocol
Channel 1 – Internal Programs, Auto Mode, Sound
Controlled Mode
Value: Function:
000 – 009 Off
010 – 029 Program 1
030 – 049 Program 2
050 – 069 Program 3
070 – 089 Program 4
090 – 109 Program 5
110 – 129 Program 6
130 – 149 Program 7
150 – 169 Program 8
170 – 189 Program 9
190 – 209 Program 10
210 – 229 Program 11
230 – 249 Auto Mode: Internal Programs
250 – 255 Sound Controlled Mode
Channel 2 – Master Dimmer (when Channel 3 on,
Channel 2 no function)
Value: Function:
000 – 009 Off
010 - 255 Dimming from 0 – 100%
Channel 3 – Strobe
Value: Function:
000 – 009 Off
010 - 255 Flash, with increasing speed
Channel 4 – Spot 1: red
Value: Function:
000 – 255 Dimming from 0 – 100%
Channel 5 – Spot 1: green
Value: Function:
000 – 255 Dimming from 0 – 100%
Channel 6 – Spot 1: blue
Value: Function:
000 – 255 Dimming from 0 – 100%
Channel 7 – Spot 2: red
Value: Function:
000 – 255 Dimming from 0 – 100%
Channel 8 – Spot 2: green
Value: Function:
000 – 255 Dimming from 0 – 100%
Channel 9 – Spot 2: blue
Value: Function:
000 – 255 Dimming from 0 – 100%
Channel 10 – Spot 3: red
Value: Function:
000 – 255 Dimming from 0 – 100%
Channel 11 – Spot 3: green
Value: Function:
000 – 255 Dimming from 0 – 100%
Channel 12 – Spot 3: blue
Value: Function:
000 – 255 Dimming from 0 – 100%
Channel 13 – Spot 4: red
Value: Function:
000 – 255 Dimming from 0 – 100%
Channel 14 – Spot 4: green
Value: Function:
000 – 255 Dimming from 0 – 100%
Channel 15 – Spot 4: blue
Value: Function:
000 – 255 Dimming from 0 – 100%
Speed control of the internal programs
For increasing speed:
Press and hold Pedal 2 (Sound controlled). Briefly press Pedal 3 (Freeze). The more often you press Pedal 3, the
quicker the speed of the internal programs.
For decreasing speed:
Press and hold Pedal 2 (Sound controlled). Briefly press Pedal 1 (Preset). The more often you press Pedal 1, the
slower the speed of the internal programs.
Replacing the fuse
Before replacing the fuse, unplug mains lead.
Step 1: Open the fuseholder on the rear panel with a fitting screwdriver.
Step 2: Remove the old fuse from the fuseholder.
Step 3: Install the new fuse in the fuseholder.
Step 4: Replace the fuseholder in the housing.
TECHNICAL SPECIFICATIONS
Power supply: 100 - 240 V AC, 50/60 Hz ~
Power consumption: 48 W
Number of 10mm LEDs: 432
Beam angle: 25°
Sound-control: via built-in microphone
Maximum ambient temperature T
a
: 45° C
Maximum housing temperature T
B
(steady state): 60° C
Min.distance from flammable surfaces: 0.50 m
Min.distance to lighted object: 0.10 m
Fuse: F 2 A, 250V
Weight: 6.5 kg
Please note: This information is subject to change without prior notice.