MacDon M100 SP Operators Manual - Manual (Page 44)

OPERATOR’S STATION
169304
42
Rev. C
(continued next page)
L1 C x x x || T O C A L I B R A T E S E L E C T
L2 M x x x || H E A D E R H E I G H T
L1 C x x x || T O C A L I B R A T E S E L E C T
L2 M x x x || H E A D E R H E I G H T
L2 M x x x || H E A D E R T I L T
L1 M x x x || H D R T I L T S E N S O R C A L
L2 M x x x || E X T E N D T L T T O S T A R T
L1 C x x x || C A L I B R A T I N G T I L T
L2 M x x x || E X T E N D T I L T H O L D
L2 M x x x || E X T E N D T I L T D O N E
L1 M x x x || H D R T I L T S E N S O R C A L
L2 M x x x || P R E S S R E T R A C T T I L T
L1 C x x x || C A L I B R A T I N G T I L T
L2 M x x x || R E T R A C T T I L T H O L D
L2 M x x x || H D R T I L T C O M P L E T E
L1 C x x x || T O C A L I B R A T E S E L E C T
L2 M x x x || H E A D E R T I L T
L2 M x x x || S T O P & E X I T
L1 C x x x || E X I T C A L I B R A T I O N ?
L2 M x x x || N O / Y E S T O C A L I B R A T E S E L E C T
L1 C x x x || D I A G N O S T I C M O D E ?
L2 M x x x ||
N O / Y E S T R A C T O R S E T U P ?
L1 C x x x || V I E W E R R O R C O D E S ?
L2 M x x x || N O / Y E S E N T E R S E N S O R S E T U P ?
L1 C x x x || V I E W T R A C T O R C O D E S ?
L2 M x x x || N O / Y E S E N T E R S E N S O R S E T U P ?
L1 1 || 1 2 3 4 . 5 H R S 1 2 3
L2 E 4 7 || S E N S O R V O L T S L O W
L1 2 || 1 2 3 4 . 5 H R S 1 2 3
L2 E 7 1 || L O W H Y D R A U L I C O I L
L1 C x x x || E X I T T R A C T O R C O D E S ?
L2 M x x x || N O / Y E S V I E W T R A C T O R C O D E S ?
L1 C x x x || E N T E R S E N S O R S E T U P ?
L2 M x x x || N O / Y E S R E A D S E N S O R I N P U T S ?
L1 C x x x || H E A D E R H T S E N S O R
L2 M x x x || E N A B L E / D I S A B L E
L1 C x x x || H E A D E R T I L T S E N S O R
L2 M x x x || E N A B L E / D I S A B L E
L1 C x x x || K N I F E S P E E D S E N S O R
L2 M x x x || E N A B L E / D I S A B L E
L1 C x x x || R E E L S P E E D S E N S O R
L2 M x x x || E N A B L E / D I S A B L E
L1 C x x x || E X I T S E N S O R S E T U P ?
L2 M x x x || N O / Y E S K N I F E S P E E D S E N S O R
The operator can select each sensor and selectively
enable or disable the sensor in the event of a sensor
malfunction.
The last 10 distinct error codes are stored along with
the code #, Exxx, engine hours and number of
occurrences. The "arrow" keys are used to cycle
between codes.
If the HEADER TILT option in the TRACTOR SETUP
is set to NO then only HEIGHT should be available
as a menu selection for calibration.
If "NO" then jump to:
If "NO" then jump to:
If "NO" then jump to:
If "NO" then jump to:
The menu will display the last item selected when the
calibration routine is completed.
If no expansion module or an A30 auger header is
selected, the corresponding menu items should be
suppressed.
Or to the first sensor "installed"
If "NO" then jump to:
If "NO" then jump to:
If "NO" then jump to:
When "SELECT" is pressed the program goes to the
EXIT SENSOR SETUP? selection.