Retsch AS 200 jet - Manual (Page 36)

Operating the machine
36
– The data are sent by the connected PC via interface cable (RS232 or USB)
to the controller PCB. The controller PCB forwards the data on to the boot
loader of the display unit.
5.16.8.4.2 Controller
– The target device controller is selected on the PC via a software update
selection menu.
– The data are sent by the connected PC via interface cable (RS232 or USB)
to the controller PCB. The controller PCB forwards the data on to the boot
loader of the display unit.
5.16.8.5 Sensor calibration
See chapter “ pressure sensor calibration ”
5.16.9 Service level
NOTE
Access to this menu point is exclusively permitted for service employees or
authorised service personnel.
Pos : 9. 51 /0020 Übersc hrift en/1.1 Ü bersc hriften/ 1. 1 Ü berschrif ten BDA/11 St arten, Unter brec hen, Stoppen @ 0\ mod_1229417133049_9.doc x @ 5070 @ 3 @ 1
5.17 Starting, Interrupting, Stopping
Pos : 9. 52 /0005 RET SCH Bedi enungs anleit ung en Kapitels ammlungen/ AS200J et /0007 AS200Jet Bedienung/ AS200J et Modul Start en Stoppe n @ 1\ mod_1239194086237_9.doc x @ 8026 @ @ 1
• Switch the device on by pressing the on/off switch at the back.
• Use the operating knob (F) to set the sieving parameters you want.
• Put the test sieve with the sample onto the nozzle compartment.
• Place the lid on the sieve.
NOTE
The sieving will not start if the lid is not on.
• Start sieving by pressing the START button (D).
• You can also start the air jet sieving directly by pressing the QUICK START
key (G). (see chapter on Quick Start key functions)
Pos : 9. 53 /0020 Übersc hrift en/1.1 Ü bersc hriften/ 1. 1 Ü berschrif te n BDA/11 Quic k Start - T ast enfunkti on @ 1\ mod_1240313233592_9. doc x @ 8229 @ 2 @ 1 Pos : 9. 54 /0005 RET SCH Bedi enungs anleit ung en Kapitels ammlungen/ AS200J et /0007 AS200Jet Bedienung/ AS200J et Modul Q uic k St art T ast enf unktion @ 1\ mod_1239194087706_9.doc x @ 8042 @ @ 1
The QUICK START (G) key can be used to start a pre-programmed sieving
process directly without accessing the menu.
Pos : 9. 55 /0020 Übersc hrift en/1.1 Ü bersc hriften/ 1. 1 Ü berschrif ten BDA/11 St and-by @ 7\ mod_1386841122969_9. doc x @ 53601 @ 2 @ 1
5.18 Stand-by
Pos : 9. 56 /0005 RET SCH Bedi enungs anleit ung en Kapitels ammlungen/ AS200J et /0007 AS200Jet Bedienung/ AS200j et M odul St and-By-M onitor @ 7\ mod_1386841015177_9. doc x @ 53590 @ @ 1
After the device has been inactive for 15 minutes (time after a STOP command),
the stand-by screen switches on automatically.
By pressing one of the buttons or touching the operating button, the stand-by
screen disappears without executing the command given.
If you were in a sub-menu when the stand-by screen was activated, you return
automatically to this selection window.
NOTE
The stand-by screen cannot be deactivated.