Barco R9002031 - Manual (Page 24)

Source connections
7-1 5975607 BARCODATA 808s 170397
4/5 Component video 8
with Tri-level sync
R, G and B with composite sync on Green;
3 RGB 3 R, G and B with separate composite or with separate Horizontal
and Vertical sync.
Port No Projector input Numeric button Description of input signal
1 Composite Video 1
S-video : Y/C (luma/chroma).
The Composite video can also be connected to Port 2. It can be
2 S-Video / Composite Video 2 selected inside the "Picture Tuning" menu. Please refer to the
Owner's Manual of this projector.
7
SOURCE CONNECTIONS
Signal input connection
The following signals can be connected to the projector through the
inputs on the back panel of the projector :
•
Composite Video
•
S-Video
•
RGB
•
Component Video
•
RGB with Tri-level sync
•
Component video with Tri-level sync
21 2))
P OWER / MAIN S
'Ãr vƒur hy† S B 7 8‚€ƒCT’pWT’p
COMM. PO RT P ORT 3 PORT 4/5
W‚€Ã D‚€ A r„
TrrÃv†‡hyyh‡v‚Ãv†‡ ˆp‡v‚†Ãirs‚ rÃp‚rp‡vtГ‡‚Г‡urГ†ˆƒƒy’ W‚v ÃyhÁ‚‡vprÃqv†‡hyyh‡v‚Ãh‰ h‡Ãqrà hpp‚ qr ГhˆГ p†rhˆ
!!"ÃW &$Ã6€ƒ
$%ÃC“ T W 9@P P ÃÃà ÃÃÃPI &$ÃPu€ W 9@P t r r  Г)Г‚ ƒ r h ‡v‚ 
r q Г)Г† ‡h  q i ’
PORT 2 PO RT 1
P ÃÃà ÃÃÃPI &$ÃPu€
PROJE CT OR MODE
1 2 3 4 5
Uuv†Ãqr‰vprÃp‚€ƒyvr†Ãv‡uÃh ‡Г $Г‚s ‡urÃA88à ˆyr†ÃÃPƒr h‡v‚Гv†Г†ˆiwrp‡Ã‡‚ s ‚ yy ‚ v t Г ‡‚Г p‚ qv ‡ v‚ †Г   Г Г Uuv † q vp Г ’Г‚‡Гp † Гu s yÃv‡  s p à qГ!Г‡uv†Ãq vp Г †‡Г pp ‡Ã ’Ãv‡ s p à p v qà vpy qvtÃv‡ s p Çu ‡Ã ’Ãp † q †v q ‡v‚Å
75 Ω Termination Switch
R, G and B with composite sync on Green;
4/5 RGB 4 or 5 R, G and B with separate composite or with separate
Horizontal and Vertical sync.
R-Y, Y, B-Y with composite sync on Y;
4/5 Component video 6 or with separate composite or with separate Horizontal and
Vertical sync.
R, G and B with Tri-level sync on Green;
4/5 RGB with Tri-level sync 7 R, G and B with separate Tri-level sync or with separate
Horizontal and Vertical Tri-level sync.
R-Y, Y, B-Y with Tri-level sync on Y; or with separate Tri-level
sync or with separate Horizontal and Vertical Tri-level sync.
Only available when the optional Tri-level sync module is installed.
Connecting a Composite Video source to
Port 1
Composite video signals coming from a VCR, OFF air signal decoder
and so on can be connected to Port 1.
To select the video input :
Press the numeric button 1 on the RCU or the local keypad.
75 W Termination Switch for Video
Terminate the video input of the projector using the 75W switch next
to the video input, when the projector operates alone or when the
projector is the last unit in a loop-through configuration.
The switch is set to "ON" : signal terminated.
The switch is set to "OFF" : signal not terminated.