Barco R9002031 - Manual (Page 6)

Safety instructions
1-1 5975607 BARCODATA 808s 110397
1
SAFETY INSTRUCTIONS
Projectors are built in accordance with the requirements of the
international safety standards IEC950, UL 1950 and CSA C22.2 No.
950, which are the safety standards of information technology
equipment including electrical business equipment.
These safety standards impose important requirements on the use
of safety critical components, materials and isolation, in order to
protect the user or operator against the risk of electric shock and
energy hazard, and having access to live parts.
Safety standards also impose to the internal and external tempera-
ture variations, radiation levels, mechanical stability and strength,
enclosure construction and protection against risk of fire.
Simulated single fault condition testing ensures the safety of the
equipment to the user even when the equipment's normal operation
fails.
Installation instructions
Before operating your projector please read this manual thoroughly,
and retain it for future reference.
Installation and preliminary adjustments should be performed by
qualified BARCO personnel or authorized BARCO service dealers.
OWNER’S RECORD
The article number (Art. No.) and serial number (Ser. No) are located
at the rear of the projector. Copy these numbers in the spaces
provided below. Refer to them whenever you call upon your BARCO
dealer regarding this product.
Article number :
Serial number :
Dealer :
The lightning flash with an arrowhead within a
triangle is intended to tell the user that parts inside
this product risk electrical shock to persons.
The exclamation point within a triangle is intended
to tell the user that important operating and/or
servicing instructions are included in the technical
documentation for this equipment.
Warning :
To prevent fire or electrical shock hazard,
do not expose this projector to rain or moisture
Federal Communication Commission (FCC statement)
This equipment has been tested and found to comply with the limits
for a class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Instructions to the user :
If this equipment does cause interference to radio or television
reception, the user may try to correct the interference by one or more
of the following measures :
* Re-orientate the receiving antenna for the radio or television.
* Relocate the equipment with respect to the receiver.
* Plug the equipment into a different outlet so that the equipment and
receiver are on different branch circuits.
* Fasten cable connectors to the equipment with mounting screws.
Note :
The use of shielded cables is required to comply within the limits
of Part 15 of FCC rules and EN55022.
General safety instructions :
* All the safety and operating instructions should be read before using
this unit.
* The operating instruction manual should be retained for future
reference.
* All warnings on the projector and in the documentation manuals
should be adhered to.
* All instructions for operating and use of this equipment must be
followed precisely.
On safety
* This product should be operated from an AC power source.
* This projector may be connected to an IT power system.
* Operating AC power voltage of the projector when leaving the
factory:
BARCODATA 808s
Art. No.: R9002031 (230 VAC) Art. No.: R9002038 (120 VAC)
Consult the appropriate section of this manual to switch over from
230 Vac to 120 Vac or from 120 Vac to 230 Vac.
If you are not sure of the type of AC power available, consult your
dealer or local power company.
* This product is equipped with a 3-wire grounding plug, a plug having
a third (grounding) pin. This plug will only fit into a grounding-type
power outlet. This is a safety feature. If you are unable to insert the
plug into the outlet, contact your electrician to replace your obsolete