Tweco 6000GST Cutting Systems - Manual (Page 64)

APPENDIX
A-18
Man
ual 0-2690
APPENDIX 2:
CUTTING SPEED CHAR
TS FOR
MERLIN 6000GST SYSTEMS (contin
ued)
NOTE
If the Optional Secondary Gas/Water Flow Control is used on the Gas Control Module, then the Gas HIGH-FLOW/LOW-FLOW
switch must be in the HIGH-FLOW position.
US Measurements
Air Plasma Cutting Data Chart
Maximizer 300 Torch
Stainless Steel - Underwater (Water Table)
Air Plasma / Air Secondary
Electrode
Gas
Distributor
Tip End Cap Amperage
Output
Volts
Speed Standoff
Plasma
Pressure
Plasma
Flowball
Secondary
Pressure
Pierce
Delay
Pierce
Height
inches Gauge Cat. No. Cat. No. Cat. No. Cat. No. amps vdc inches/min inches psi psi seconds inches
1/16 20-1018 20-0008 20-1031 20-1028 100 145 400 0.188 80 90 75 0.00 0.200
1/8 20-1018 20-0008 20-1031 20-1028 100 150 200 0.188 80 90 75 0.10 0.200
3/16 20-1018 20-0008 20-1031 20-1028 100 150 130 0.188 80 90 75 0.20 0.200
1/4 20-1018 20-0008 20-1031 20-1028 100 150 70 0.188 80 90 75 0.30 0.200
3/8 20-1018 20-0008 20-1031 20-1028 100 160 50 0.188 80 90 75 0.50 0.200
1/4 20-1018 20-0008 20-1032 20-1028 150 145 150 0.250 80 90 75 0.00 0.375
3/8 20-1018 20-0008 20-1032 20-1028 150 150 100 0.250 80 90 75 0.00 0.375
1/2 20-1018 20-0008 20-1032 20-1028 150 155 80 0.250 80 90 75 0.25 0.375
5/8 20-1018 20-0008 20-1032 20-1028 150 160 50 0.250 80 90 75 0.25 0.375
3/4 20-1018 20-0008 20-1032 20-1028 150 165 25 0.250 80 90 75 0.50 0.500
1/2 20-1018 20-0008 20-1033 20-1028 225 140 125 0.250 80 90 75 0.00 0.380
5/8 20-1018 20-0008 20-1033 20-1028 225 145 95 0.250 80 90 75 0.25 0.380
3/4 20-1018 20-0008 20-1033 20-1028 225 145 65 0.250 80 90 75 0.50 0.500
1 20-1018 20-0008 20-1033 20-1028 225 150 35 0.312 80 90 75 0.50 0.500
3/4 20-1021 20-1009 20-1034 20-1028 300 145 70 0.250 80 120 75 0.25 0.500
1 20-1021 20-1009 20-1034 20-1028 300 155 40 0.250 80 120 75 0.50 0.500
1 1/2 20-1021 20-1009 20-1034 20-1028 300 170 20 0.375 80 120 75 NR NR
Material
Thickness
Art # A-02704
Torch Body
180˚ 9-6410
70˚ 9-6457 90˚: 9-6459
End Cap
(See Chart)
Tip
(See Chart)
Gas Distributor
(See Chart)
Electrode
(See Chart)
Shield Cup Body
No. 20-1029
NOTE:
If using a torch height control which
offers an ohmic sensing feature, select a
shield cup body with an ohmic clip tab.
Use catalog # 20-1427 for normal cut-
ting and catalog 20-1428 for cutting
underwater.