Great Plains EWNT7 1523Q-1630Q Operator Manual - Manual (Page 5)

-
3 4/25/06 Great Plains Mfg., Inc.
Section 1 Safety Rules
EWNT7 and EWNT10 End Wheel No Till Drill 150-082M-A
Most accidents are the result of negligence and care-
lessness, usually caused by failure of the operator to fol-
low simple but necessary safety precautions. The
following safety precautions are suggested to help pre-
vent such accidents. The safe operation of any machin-
ery is a big concern to consumers and
manufacturers.Your End Wheel No-Till has been de-
signed with many built-in safety features. However, no
one should operate this product before carefully reading
this operator’s manual.
General Operation & Repair
1. Never allow the drill to be operated by anyone who is un-
familiar with the operation of all functions of the unit. All
operators should read and thoroughly understand the in-
structions given in this manual prior to moving the unit.
2. Make sure safety rules are understood before operating
machinery or tractor.
3. Never permit any persons other than the operator to ride
on the tractor.
4. Never permit any persons to ride on or stand near the
drill while it is in operation.
5. Regulate your speed to the field conditions, maintaining
complete control at all times.
6. After repairing or adjusting, make sure all tools and
parts are removed from the implement before attempting
to operate it.
7. Do not grease or oil machine while it is in operation.
8. Loose fitting clothing should not be worn as it may catch
in moving parts.
9. Never dismount from a moving tractor.
10. Do not leave the tractor or the implement unattended
with the engine running.
11. Do not stand between the tractor and the implement dur-
ing hitching.
12. Detach and store implements in an area where children
normally do not play. Stabilize implements by using suit-
able supports and block wheels.
13. If a hydraulic leak develops, correct it immediately. Es-
caping hydraulic oil can have extremely high pressure. A
stream of high pressure oil may easily penetrate the skin.
It is imperative that the connections are tight and that all
lines and pipes are in good condition. If an injury is
caused by the escaping hydraulic fluid, see doctor at
once!
14. Use a piece of cardboard or wood to detect leaks of hy-
draulic oil under pressure.
15. Be sure to relieve all hydraulic pressure before disconnec-
tion any lines or pipes between the implement and the trac-
tor hydraulic system. Keep all guards and shields in place.
Transporting
1. Use good judgement when transporting tractor and im-
plements on the highway. Always maintain complete con-
trol of the machine.
2. Limit transport speed to 20 mph. Transport only with a
farm tractor of sufficient size and horse power. See
“Tractor Requirements” Section 2,page 8.
3. Always make sure flashing safety lights, “Slow Moving
Vehicle” emblem, and reflectors are in place and visible
prior to transporting the machine on public roads.
4. Know your state and local laws concerning highway
safety and regulations. Comply with these laws when
transporting machinery.
5. Use warning flags or approved warning lights at night
and during other periods of poor visibility. Do your best
to prevent highway accidents.
Tire Handling & Repair
1. Tire changing can be dangerous and should be pre-
formed by trained personnel using the correct tools and
equipment.
2. Do not re-inflate a tire that has been run flat or seriously
under inflated. Have it checked by qualified personnel.
3. When removing and installing wheels, use wheel han-
dling equipment adequate for the weight involved.
Safety Decals
1. Your End Wheel No-Till comes equipped with all safety
decals in place. They were designed to help you safely
operate your drill. Read and follow their directions.
2. Keep safety decals clean and legible.
3. Replace all damaged or missing safety decals. To order
new safety decals go to your Great Plains dealer and re-
fer to the parts section for safety decal package part num-
ber.
4. Replace these decals whenever they become worn or un-
readable. To install new safety decals:
a. Clean the area the decal is to be placed
b. Peel backing from the decal. Press firmly on to sur-
face being careful not to cause air bubbles under the
decal.
Section 1
Safety Rules
!