Great Plains ADC2350B Assembly Instructions - Manual (Page 4)

Great Plains Mfg., Inc.
4 Auger Carrier Update
166-255M 03/05/2009
11. Select two (2) each new:
816-562C 8 INCH AUGER REST PAD
(this is the longer of the two sizes of EPDM pads)
and eight (8) sets new:
802-888C ELEVATOR BOLT 1/4-20X3/4 PLT:
804-006C WASHER LOCK SPRING 1/4 PLT
803-006C NUT HEX 1/4-20 PLT
12. The clamp pad may have no holes (or two holes,
or four), and may or may not have adhesive on one
side, protected by release paper. If four holes are
not present, it is necessary to assembly-drill them.
Position the pad so that it is centered in the latch
weldment
. Mark holes for fractional size
9 ⁄
32
in
(letter size K, 7.2mm). Remove pad and punch or
drill holes.
13. Remove any release paper. Position a rest pad ,
adhesive side to inside of latch face. Insert the ele-
vator bolts
through the inside of the pad and
secure with lock washers and nuts .
Refer to Figure 5
14. Select the hook side of two (2) each new:
800-285C AUGER LATCH CLAMP
and four (4) sets new:
802-007C HHCS 5/16-18X3/4 GR5
804-009C WASHER LOCK SPRING 5/16 PLT
803-008C NUT HEX 5/16-18 PLT
Mount the hook side of the latch clamp at the top
of the carrier weldment , using the bolts , lock
washers and nuts .
Assemble New Auger Carriers
Refer to Figure 4 on page 3 and Figure 3
15. Select two (2) sets new:
802-130C HHCS 1/2-13X2 1/2 GR5
803-019C NUT LOCK 1/2-13 PLT
Mount latch assemblies at the bottom of carriers.
Assemble New Pivot Mount
Refer to Figure 6
16. Select one each new:
166-190H 20’ AUGER PIVOT MOUNT WELDMENT
800-001C GREASE ZERK STRAIGHT 1/4-28
Screw the zerk into the
1 ⁄
4
-28 threaded hole of
the mount cross-tube.
17. Select one each new:
166-189H AUGER BALANCE SPRING ANCHOR
802-045C HHCS 1/2-13X5 GR5
803-019C NUT LOCK 1/2-13 PLT
Mount spring anchor on pivot mount with
bolt . Do not fully tighten lock nut .
18. Select one each new:
802-412C HHCS 1/2-13X2 3/4 FTHD
804-015C WASHER LOCK SPRING 1/2 PLT
803-020C NUT HEX 1/2-13 PLT
and two:
804-113C WASHER FLAT 1/2 USS HARD PLT
Swing anchor up into pivot mount . Insert
bolt with flat washer . Add second flat
washer , lock washer and nut . Thread nut
on just a few turns. Do not fully seat nut at this time.
Figure 5
Auger Carrier Latch Hook
29373
12
18
17
33
27
38
25
32
26
38
13
Figure 6
Assemble Pivot Mount
29372
15
16
14
20
29
37
35
30
23
37
38
25
32 26
17
18
33
27
17
12 18
33 27
22
29
15
16
16
14
20
29
14 15
20 29
23
35
30
37
14 15
23 37
37 35 30