Great Plains 1205NT Parts Manual - Manual (Page 73)

Revision Comments Part Description Part No. Ref.
Image No. dwg14110
2nd rev. SPKT 40B14 X 3/4 HEX BORE 808-167C 1.
Use existing stock; 1st rev. REPLACED BY 808-167C 123-566D 1.
PIN ROLL 3/16X1 1/4 PLT 805-023C 2.
CHAIN RL #40 X 132 PITCHES 809-112C 3.
NUT HEX JAM 1/2-13 PLT 803-036C 4.
NO. 40 12T IDLER SPKT. 817-025C 5.
Rev. 2 is not interchangeable
w/rev. 1
HHCS 1/2-13X3 GR5 802-039C 6.
1st rev. HHCS 1/2-13X2 1/4 GR5 802-038C 6.
NUT HEX JAM 5/8-11 PLT 803-023C 7.
WASHER LOCK SPRING 5/8 PLT 804-022C 8.
WASHER FLAT 1/2 USS PLT 804-017C 9.
SPROCKET 40A17 IDLER 808-046C 10.
HHCS 5/8-11X3 1/2 FTHD 802-436C 11.
NUT HEX 5/8-11 PLT 803-021C 12.
WASHER FLAT 5/8 USS PLT 804-019C 13.
HHCS 5/8-11X1 3/4 GR5 802-053C 14.
NUT HEX 5/16-18 PLT 803-008C 15.
WASHER LOCK SPRING 5/16 PLT 804-009C 16.
FLANGETTE 52 MST 822-032C 17.
BRG 7/8HEXX2.05OD SPH 822-119C 18.
HEX SHAFT 7/8 X 26 1/2 120-233D 19.
12'EWNT TRANSFER DRIVE MOUNT 118-503D 20.
RHSNB 5/16-18X1 GR5 802-282C 21.
2nd rev. SPKT 40B22 7/8 HEX BORE & SS 808-194C 22.
Use existing stock; 1st rev. REPLACED BY 808-194C 123-567D 22.
REAR DRIVE BRG MOUNT PLATE LH 123-517D 23.
2nd rev. SPKT 40B12 7/8 HEX BORE W/SS 808-143C 24.
Use existing stock; 1st rev. RPBY 808-143C 123-568D 24.
HHCS 1/2-13X1 1/2 GR5 802-091C 25.
WASHER FLAT 1/2 SAE PLT 804-016C 26.
WASHER LOCK SPRING 1/2 PLT 804-015C 27.
NUT HEX 1/2-13 PLT 803-020C 28.
2nd rev. CHAIN RL #40 61 PITCHES 136-060D 29.
Use existing stock; 1st rev. RPBY 136-060D 809-065C 29.
2nd rev. CHAIN RL #40 100 PITCHES 136-110D 30.
Use existing stock; 1st rev. RPBY 136-110D 809-142C 30.
AGITATOR IDLER BOLT 5/8-11 118-439H 31.
HHCS 5/8-11X1 1/4 GR5 802-050C 32.
SPKT 40B17X3/4 HEXBR&LCK COLLR 118-592H 33.
SCREW SET 5/16-18 SKT KP X 3/8 801-035C 34.
11/13/12 - 73 - 150-131P
Table of Contents Part Number Index
Drive
Agitator Drive
(Applies to 1205NT only)