Great Plains TC5319 Parts Manual - Manual (Page 71)

Revision Comments Part Description Part No. Ref.
Image No. dwg41148
PLATE - TORCHED 586-182D 1.
C-FLEX BRG HANGER 1X3 807-229C 2.
GANG BRACKET MOUNT 586-186D 3.
CASTING TOP BEARING 812-006CP 4.
BRG INS 1.78ID CDS211TTR23N 822-026C 5.
CASTING BOTTOM BEARING FINI 586-187D 6.
BEARING SHIELD 556-375D 7.
HALF SPOOL TURBO COULTER 566-004D 8.
COULTER TURBO 22X.197X1.78 820-350C 9.
FULL SPOOL 7 1/2 TURBO COUL 566-003D 10.
5 Blade Gang @ 7.5" Space GANG BOLT - 35 1/2 567-010D 11.
6 Blade Gang @ 7.5" Space GANG BOLT - 43 567-002D 11.
7 Blade Gang @ 7.5" Space GANG BOLT - 50 1/2 567-003D 11.
8 Blade Gang @ 7.5" Space GANG BOLT - 58 567-004D 11.
9 Blade Gang @ 7.5" Space GANG BOLT 65 1/2" TURBO TIL 586-087D 11.
WASHER FLAT 3/4X6 1/2X3/4 T 586-056D 12.
WASHER DURA-TIGHT 1.81ID X 804-200C 13.
WASHER MACH 2 1/2X1 3/4X10G 804-205C 14.
NUT HEX SLOTTED 1 3/4-5 REG 803-339C 15.
Rev. 2 HHCS 5/16-18X3 1/4 GR5 802-390C 16.
Rev. 1 Replaced by 802-390C HHCS 1/4-20X3 1/4 GR8 802-842C 16.
Rev. 1 (S/N A1174X+) SCRAPER BAR MOUNT 567-001D 17.
SCRAPER BAR - 27 1/2 567-006D 18.
SCRAPER BAR 35" TT 586-188D 18.
SCRAPER BAR - 42 1/2 567-007D 18.
SCRAPER BAR - 50 567-008D 18.
SCRAPER BAR - 57 1/2 567-009D 18.
SCRAPER - TURBO CHISEL 567-005D 19.
Requires Lock Nut item 31 SCRAPER 9 1/2" TURBO TILL 586-093D 20.
HHCS 3/4-10X6 GR5 802-070C 21.
WASHER LOCK SPRING 3/4 PLT 804-023C 22.
NUT HEX 3/4-10 PLT 803-027C 23.
Rev. 3 (S/N A1053X+) 802-469C Bolt Must
be used when Replacing 812-006CP
& 566-187D.
HHCS 3/4-10X8 GR5 PLT 802-469C 24.
Rev. 2 (S/N A1052X-) HHCS 3/4-10X7 1/2 GR5 802-280C 24.
Rev. 1 HHCS 3/4-10X7 GR5 802-095C 24.
HHCS 5/8-11X7 GR5 802-262C 25.
WASHER LOCK SPRING 5/8 P 804-022C 26.
NUT HEX 5/8-11 PLT 803-021C 27.
U-BOLT 1/2-13 X 2 X 3 GR 5 806-005C 28.
WASHER LOCK SPRING 1/2 PLT 804-015C 29.
NUT HEX 1/2-13 PLT 803-020C 30.
NUT LOCK 3/4-10 PLT 803-026C 31.
WASHER FLAT 1/4 USS PLT 804-075C 32.
Rev. 2 NUT HEX NYLOCK 5/16-18 PLT 803-084C 33.
Rev. 1 Replaced by 803-084C NUT HEX NYLOCK 1/4-20 803-255C 33.
ZERK GREASE STRAIGHT 1/8-27 800-130C 34.
Rev. 2 DELTA SCRAPER 7.5 SPACING 586-648D 35.
Rev. 1 DELTA SCRAPER TURBO CHISEL 567-011D 35.
07/14/14 - 71 - 566-046P
Table of Contents Part Number Index
Section 5: Gangs
Turbo Gang Assembly
(Applies to TC5109 (S/N A1419X-), TC5111 (S/N A1419X-), TC5113 (S/N A1419X-), TC5115 (S/N A1419X-),
TC5313 (S/N A1419X-), TC5315 (S/N A1419X-), TC5317 (S/N A1419X-), TC5319 (S/N A1419X-), TC5321 (S/N
A1419X-), TC5323 (S/N A1419X-) only)