Great Plains TC5319 Parts Manual - Manual (Page 75)

Revision Comments Part Description Part No. Ref.
Image No. dwg41269
SHANK SUB-WELDMENT 569-005H 1.
SHANK SUB-WELDMENT 569-007H 2.
HHCS 3/4-10X2 1/2 GR5 802-212C 3.
WASHER LOCK SPRING 3/4 PLT 804-023C 4.
NUT HEX 3/4-10 PLT 803-027C 5.
Rev. 2 SLEEVE BEARING 3/4 I.D. 817-910C 6.
Rev. 1 Replaced by 817-910C BUSHING 1ODX.78IDX4.24 566-076D 6.
Rev.2 (S/N A1116X+) SHANK SUB WELDMENT 569-203H 7.
Rev.1 Replaced by 569-203H (S/N A1115X-) SHANK SUB-WELDMENT 569-192H 7.
HHCS 3/4-10X6 1/2 GR5 802-360C 8.
Rev.2 (S/N A1116X+) BUSHING 569-089D 9.
Rev.1 Replaced by 569-089D (S/N A1115X-) BUSHING 1ODX.78IDX2.102 569-014D 9.
SHANK SPRING BOLT WELDMENT 569-193H 10.
HHCS 3/4-10X4 1/2 GR5 802-192C 11.
SPRING COMP 3.625OD .6875W 16L 807-287C 12.
Rev. 2 WASHER FLAT 1 USS PLT 804-028C 13.
Rev. 1 Replaced by 804-028C SHANK SPRING BOLT TIGHTENER 589-132H 13.
NUT HEX JAM 1-8 PLT 803-030C 14.
SHANK CHISEL 1 1/4X2X25 1/2 820-368C 15.
HHCS 1/2-13X3 GR5 802-039C 16.
WASHER LOCK SPRING 1/2 PLT 804-015C 17.
NUT HEX 1/2-13 PLT 803-020C 18.
Rev.2 (S/N A1116X+) HHCS 5/8-11X4 1/2 GR5 802-100C 19.
Rev.1 Replaced by 802-100C (S/N A1115X-) HHCS 5/8-11X3 1/2 GR5 802-162C 19.
WASHER LOCK SPRING 5/8 PLT 804-022C 20.
NUT HEX 5/8-11 PLT 803-021C 21.
TWISTED SHOVEL 1/2X3X23 RH 820-336C 22.
TWISTED SHOVEL 1/2X3X23 LH 820-337C 22.
TWISTED SHOVEL 1/2X4X26 RH 820-332C 22.
TWISTED SHOVEL 1/2X4X26 LH 820-333C 22.
Shown CHISEL POINT 5/8X2X15 820-032C 22.
CHISEL POINT WINGED 5/8X2X15 569-162H 22.
PLOW 1/2-13X2 1/2 GR5 802-590C 23.
WASHER FLAT 1/2 USS PLT 804-017C 24.
NUT HEX TOP LOCK 1/2-13PLT 803-342C 25.
07/14/14 - 75 - 566-046P
Table of Contents Part Number Index
Section 6: Shanks
Chisel Shank Assembly (569-195S)
(Applies to TC5109 (S/N A1419X-), TC5111 (S/N A1419X-), TC5113 (S/N A1419X-), TC5115 (S/N A1419X-),
TC5313 (S/N A1419X-), TC5315 (S/N A1419X-), TC5317 (S/N A1419X-), TC5319 (S/N A1419X-), TC5321 (S/N
A1419X-), TC5323 (S/N A1419X-) only)