Great Plains 6548 Series VII Field Cultivator-Floating Hitch Parts Manual - Manual (Page 11)

Revision Comments Part Description Part No. Ref.
Image No. dwg00402
CENTER FRAME TRUSS 575-550H 1.
GAUGE WHEEL ARM MOUNT 575-558H 2.
GAUGE WHEEL ARM RH (BOTTOM) 575-555H 3.
GAUGE WHEEL ARM LH (BOTTOM) 575-556H 4.
GAUGE WHEEL ARM (TOP) 575-554H 5.
HITCH POLE FLOATING 6500FC VII 575-542H 6.
CLEVIS (LARGE FC/DC) 560-024H 7.
HITCH BOLT 11 550-037H 8.
Use as needed WASHER MACH 2.25 X 1.50 X 10GA 804-063C 9.
NUT HEX SLOTTED 1 1/2-6 PLT 803-301C 10.
PIN COTTER 1/4 X 3 PLT 805-115C 11.
HOSE SUPPORT 550-001H 12.
PIN COTTER 1/8 X 1 1/2 805-225C 13.
Rev. 2 SCREW JACK 30' DRILLS 890-007C 14.
Rev. 1 Replaced by 890-007C ADJ JACK SWIVEL TOP-WIND 2000# 890-780C 14.
Rev. 2 HHCS 1 1/4-7X7 GR8 PLT 802-795C 15.
Rev. 1 Changed to 802-795C HHCS 1 1/4-7X6 1/2 GR8 PLT 802-784C 15.
Rev. 2 NUT HEX TOP LOCK 1 1/4-7 PLT 803-314C 16.
Rev. 1 Replaced by 803-314C NUT HEX LOCK 1 1/4-7 PLT 803-317C 16.
1 x 5 1/2" SP GREASABLE BOLT 575-035D 17.
NUT HEX 1-8 NYLON INSERT PLT 803-038C 18.
Rev. 2 See item 14, previous page PIN CLEVIS 1 X 3 3/8 USABLE 805-351C 19.
Rev. 1 Changed to 805-351C PIN CLEV 1X2 3/8 USE MUSHRM HD 805-352C 19.
PIN COTTER 3/16 X 2 805-058C 20.
WASHER MACH 1.5X1.00X.075 804-192C 21.
U-BOLT 3/4-10X3 1/32X5 3/8 806-200C 22.
WASHER LOCK SPRING 3/4 PLT 804-023C 23.
NUT HEX 3/4-10 PLT 803-027C 24.
HHCS 3/4-10X2 GR5 802-064C 25.
HHCS 5/8-11X1 1/2 GR5 802-051C 26.
WASHER LOCK SPRING 5/8 PLT 804-022C 27.
NUT HEX 5/8-11 PLT 803-021C 28.
MANUAL PAK TUBE 817-609C 29.
CLAMP WORM DRIVE (3"-5") 800-231C 30.
1 1/4 X 1 X 3/4 HDR BUSHING 890-143C 31.
SAFETY CHAIN 16100 LB 890-824C 32.
SAFETY CHAIN SPACER 576-048D 33.
WASHER FLAT 1 1/2 SAE PLT 804-071C 34.
12/09/09 - 11 - 560-205P
Table of Contents Part Number Index
Section 2: Frames
Center Caster Wheel Linkage & Hitch
(Applies to 6330FC F H, 6332FC F H, 6537FC F H, 6539FC F H, 6541FC F H, 6544FC F H, 6546FC F H, 6548FC
F H only)