Great Plains YP2425A-3620 36 Row 20-Inch Quick Start - Manual (Page 5)

Quick Setup Guide for IntelliAg Model YP24 20” Air Pro
11001-1521-200908
©2009 DICKEY-john Corporation
Specifi cations subject to change without notice.
System Component Installation
Locate and install system components as shown in the diagram.
Note how the modules are identifi ed and which modules are located
on which sections in this system.
Connect WSMB module harnesses together with included exten-
sions. Modules connect to the WSMT harness connection. Plug all
unused connectors with included dust plugs.
Secure any excess wires with tie wraps.
See Operator’s manual for additional installation information.
Power on monitor and program with correct constants as described
on this Quick Start Guide.
1.
2.
3.
4.
5.
5
467980845
30’ Extension
Harness
WSMB Module
Harness
467981201A
WSMB
Module
Seed Monitor
467981100S1
467980143
Extension
Harness
WSMT
Module
Harness
467980151
Connect to
Actuator
Harness
467980160
467980143
Extension
Harness
Standard Dj SE Style
Planter Harness
Left Section
467981706
Rows 1-14
WSMB
Module
WSMB
Module
Harness
467981201A
Seed Monitor
467981100S1
Standard Dj SE Style
Planter Harness
Right Section
467981706
Rows 23-36
Can
Terminator
Connect Cab Harness
to Implement Can
Harness
Radar Speed Sensor
467833000S1
Mounting Kit
467830760
(Radar connected to either
tractor harness or WSMT
as shown below)
Virtual
Terminal
Chassis
Ground
CAN
Terminator
467980126
Ignition
Connect to
switched +12VDC.
NOTE: This wire
must be connected to
switched +12VDC
Master
Switch
(467980124S1)
+ -
Tractor Cab Harness
467980455
Battery
CFM
Tractor ECU
Controller
(467985060S1)
Harness
467980452
(5” Terminal) or
Harness
467980451A
(10” Terminal)
467984220S1
Tractor Harness
RS232
GPS
(467980451 Harness)
Implement CAN
Breakaway Harness 6’
467980134
Connect to Optional
Hydraulic Tongue Harness
or to Extension
467983502
467982000S1
Hydraulic
Tongue
Option Connect to
Harness 467980134
Connect to
467980144
Extension
Note: Connect the WSMT
Actuator Harness and the
Dj Planter Harness to the
mating connectors of the
WSMT Module Harness
Connect to
tractor harness
Planter
Output
Module
464820517
Output 2 Hitch B1
Output 2 Hitch B2
Output 1 Lift
467980144
Extension
Harness
467980361
Rear Hitch
Harness
467980136
Extension
Harness
Pump Clutch
464820518S1
4667980470 Extension
Planter
Output
Module
467983503
467982000S1
Fertilizer Pump
Option
Boom 3 and
Bypass 467980430
Output 1
(Not Used)
Output 2
Boom 1 and 2
467980430
Can
Terminator
Output 1
Left Clutch
464820517S1
2 Solenoid Driver
Output 1
Marker
Output 2
Fold
Planter
Output
Module
464820511S1
2 Solenoid Driver
467983504
467982000S1
Clutch
Control
467980471
Extension 20’
Output 1
Right
Clutch
464820518S1
2 Solenoid Driver
Output 2
to Fold
Lock Valve
WSMT II
467980815S1
Accessory Sensors
connection to WSMT
ACTUATOR HARNESS
467980160
Application
Rate Sensor
(Channel 1-4 Feedback)
Labeled FB1-FB4
Hopper
Level Sensor
466820720S3
Implement Lift Sensor
464820520S1
If no implement lift
sensor is used, connect
the IMP LIFT leads
together
Fan/Shaft
RPM Sensor
466970014S1
Radar Speed Sensor
46783300S1
(Radar connected to
either tractor harness
or WSMT as shown below)
Servo Valves
(Labeled Servo 1 and Servo 2)
Actuator Harness
467980160
Test Switch
I mplement
Lift Extension
Harness
466820713
Actuator
467096050
20’ Harness
457901814 Adapter
467980172
PWM Solenoid Valves
466820832S1
Pressure
Sensor
467980496
17’ Harness
457901823
CFM Harness
467980330
Hopper Extension
Harness
466820714
Fan
Extension
Harness
459680922
467980473
Extension 30’
Output 2 Center Clutch
Standard Dj SE Style
Planter Harness
Middle Section
467981707
Rows 15-22
Hopper Level
Sensor
466820720S3
467980410
Hopper
Harness
Hopper Extension
Harness
466820714