Crown Boiler CWD138 - Manual (Page 20)

18 18
TABLE 4: PERMISSIBLE VENT SYSTEMS AND PRINCIPLE VENT COMPONENTS
MANUFACTURER VENT SYSTEM SIZE
CONDENSATE
TRAP
WALL
THIMBLES
HORIZONTAL
TERMINATION
VERTICAL
TERMINATION
HEAT FAB
SAF-T VENT
EZ SEAL
3
9321
(NOTE 3)
7393GC
7393GCS
5391CI
ELBOW: 7314TERM
TEE: 7390TEE
5300CI
4
9421
(NOTE 3)
7493GC
7493GCS
5491CI
ELBOW: 7414TERM
TEE: 7490TEE
5400CI
SAF-T VENT SC
3
SC03DRN
(NOTE 3)
SC03FS
SC03FSA
ELBOW (NOTE 5):
SC03HT + 7314TERM
TEE (NOTE 5):
SC03HT + 7390TEE
5300CI + SC03VT
(NOTE 6)
4
SC04DRN
(NOTE 3)
SC04FS
SC04FSA
ELBOW (NOTE 5):
SC04HT + 7414TERM
TEE (NOTE 5):
SC04HT + 7490TEE
5400CI
+ SC04VT
(NOTE 6)
PROTECH
SYSTEMS
INC.
FASNSEAL
3 FSHDT3 FSWT3
ELBOW: FSELB9003 + FSBS3
TEE: FSTT3
FSRC3
4
FSHDT4
OR FSCD4
(NOTE 4)
FSWT4
ELBOW: FSELB9004 + FSBS4
TEE: FSTT4
FSRC4
FASNSEAL W2
3
W2-T3
+W2-DF3
W2-WT3
ELBOW: FSA-SWDW3
+ FSELB9003 + FSBS3
TEE: FSA-SWDW3 + FSTT3
W2-RC3
4
W2-T4
+ W2-DF4
W2-WT4
ELBOW: FSA-DWSW4
+ FSELB9004 + FSBS4
TEE: FSA-SWDW4 + FSTT4
W2-RC4
Z-FLEX
SVE
SERIES III
(“Z-VENT III”)
3 SVEDWCF03 2SVSWTEF03
ELBOW: 2SVSTEX0390
TEE: 2SVSTTF03
2SVSRCF03
4 SVEDWCF04 2SVSWTEF04
ELBOW:
2SVEEWCF0490 + 2SVSTPF
TEE: 2SVSTTF04
2SVSRCF04
METAL-FAB CORR/GUARD
3 CGSWDS(3”) CGSWWPK(3”)
ELBOW: CGSW90LTM(3”)
TEE: CGSWTTM(3”)
CGSWC(3”)
4 CGSWDS(4”) CGSWWPK(4”)
ELBOW: CGSW90LTM(4”)
TEE: CGSWTTM(4”)
CGSWC(4”)
NOTES:
1) See vent system manufacturer’s literature for other part numbers that are required such as straight pipe, elbows, fi restops and
vent supports.
2) In addition to terminals shown, Crown coaxial terminals may be used in some cases. See Table 3 for applications and Crown
part numbers.
3) All Heat Fab condensate traps shown may be installed in vertical or horizontal run.
4) Protech FSCD4 condensate trap may be installed in a vertical or horizontal run. All other Protech traps must be installed in a
horizontal run only.
5) Heat Fab Saf-T Vent SC may not be used for horizontal coaxial venting - a separate air inlet pipe must be provided for hori-
zontal direct vent systems. SC03HT or SC04HT adapters are used to adapt from SC pipe to terminal. Use of SC pipe in horizon-
tal systems does allow for reduced clearances to combustibles in some applications. See Table 2.
6) Heat Fab SC03VT or SC04VT adapters are required on any vertical vent system using Saf-T Vent SC even when combustion
air is obtained through a separate pipe or from the boiler room.
7) Metal-Fab CGSWDS condensate traps may only be installed in a horizontal run.