Crestron electronic Isys TPS-17W - Manual (Page 47)

ISYS ® TILT TOUCHPANELS
Isys ® Tilt Touchpanel Accessories
www.crestron.com | 800.237.2041 | 201.767.3400
© 2007 Specifications subject to change without notice
tilt touchpanels
INTERFACE MODULES AND CABLES
QM-TX QuickMedia™ Transmitter
The QM-TX provides a low-cost multimedia interface
solution for QuickMedia-based Touchpanels and
MediaManager systems. Portable or rack-mounted,
the QM-TX can be used to send audio, video, and
computer signals to any QM-equipped touchpanel via
Crestron’s exclusive single-wire QuickMedia transport.
Five BNC’s are provided on the QM-TX to accept
composite, S-Video, component, HDTV, or RGB
signals (up to 1600 x 1200 at 60 Hz). Balanced stereo
line-level audio signals are transmitted simultaneously
with 24-bit digital resolution. Video formats can be
switched dynamically and automatically under system
control. The QM-TX is 1/2-space rack-mountable
using the optional ST-RMK kit.
SPECIFICATIONS
Video
Gain: 0dB (75 ohm termination)
Bandwidth: 100MHz (-3dB) at unity gain
Formats: Supports standard definition and HDTV up to 720p
and 1080i
RGB
Gain: 0dB (75 ohm termination)
Maximum Resolution: 1600x1200 @ 60Hz (at unity gain)
with cable length of 100 meters and maximum compensation
at receiver (touchpanel)
Audio
A-D Conversion: Burr Brown 24-bit, 48 kHz
Frequency Response: 20Hz to 20kHz
Connectors
R/C/P
R
, G/Y/Y, B/COMP/P
B
, H, V: (5) BNC female
RGB/Video input
Formats: RGBHV, RGBS, RG
S
B, YP
B
P
R
, S-Video (Y/C),
composite;
Input Impedance: 75 ohms (R/C/P
R
, G/Y/Y, & B/COMP/P
B
)
Sync Impedance: 620 ohms (H and V)
Maximum Input Voltage: 0.7 V
P-P
for RGB and C of S-Video;
1 V
P-P
for composite and Y of S-Video; 5 V
P-P
for H and V Sync;
Video signal sensing on Y, COMP, and H
AUDIO: (1) 5-pin 3.5mm detachable terminal block
Balanced/unbalanced stereo line-level audio input
Maximum Input Level: 4 V
RMS
balanced, 2 V
RMS
unbalanced
Input Impedance: 10k ohms balanced, 5k ohms unbalanced
QM OUT: (1) 8-wire RJ45 female, QuickMedia output port
Connects to QM input port of touchpanel of other
QuickMedia device via CresCAT-QM or CresCAT-IM cable*
NET: (2) 4-pin 3.5mm detachable terminal blocks
Cresnet slave ports, paralleled
Connect to Cresnet control network
G: (1) 6-32 screw, chassis ground lug
LED Indicators
PWR: (green) Indicates DC power supplied from
Cresnet network
NET: (yellow) Indicates communication with Cresnet system
VIDEO ACT: (red) Indicates presence of a valid video
input signal
SETUP (rear): (red) Used for touch-settable ID (TSID)
Controls
SETUP: (1) Button for touch-settable ID (TSID)
Power Requirements
Cresnet Power Usage: 5 Watts (0.21 Amp @ 24 Volts DC)
Environmental
Temperature: 41° to 104°F (5° to 40°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Black metal, 0.5U 19" rack mountable using optional ST-RMK
(sold separately)
Dimensions
Height: 1.80 in (4.57 cm)
Width: 7.07 in (17.96 cm)
Depth: 7.02 in (17.83 cm)
Weight
2.05 lbs (0.93 kg)
AVAILABLE ACCESSORIES
ST-RMK
Rack Mount Kit
* For QuickMedia wiring use CresCAT-QM or CresCAT-IM cable;
the maximum aggregate cable length and delay skew between
any QM transmitter (origination point) and QM receiver (endpoint)
is 450 ft (137 m) and 22 nS.
47