Kontron NSC2U IP Network Server User Manual
Kontron ip network server nsc2u
Advertising
Table of contents
Document Outline
- 1 Introduction
- 1.1.1 Manual Organization
- 2 Features
- 2.5.1 SFP Board Features
- 2.8.1 Full-height PCI-X/PCIe Riser Card
- 2.8.2 Low-profile PCIe Riser Card
- 2.10.1 CPU 1 and Memory Cooling Area
- 2.10.2 CPU 2 and Chipset Cooling Area
- 2.10.3 PCI Cooling Area
- 2.10.4 Hard Disk Drive and Power Supply Cooling
- 2.10.5 Fan Speed Control
- 2.10.6 Cooling Summary
- 2.11.1 Processor
- 2.11.2 Memory
- 3 Server Component Installations and Upgrades
- 3.1.1 Tools and Supplies Needed
- 3.1.2 System References
- 3.2.1 Removing the Chassis Cover
- 3.2.2 Installing the Chassis Cover
- 3.2.3 Removing the Front Bezel
- 3.2.4 Installing the Front Bezel
- 3.2.5 Removing the Processor Air Duct
- 3.2.6 Installing the Processor Air Duct
- 3.3.1 Installing or Replacing a Hard Drive
- 3.3.2 Replacing a Power Supply
- 3.4.1 Configuring Jumpers on the Server Board
- 3.4.2 Configuring Memory DIMMs
- 3.4.3 Installing DIMMs
- 3.4.4 Removing Memory DIMMs
- 3.4.5 Adding or Replacing a Processor
- 3.4.6 Other Installation and Upgrade Options
- 3.5.1 Connecting the Power Cord
- 3.5.2 Equipment Rack Precautions
- 4 Optional Component Installations
- 4.1.1 Tools and Supplies Needed
- 4.1.2 System References
- 4.1.3 Cable Routing Reference
- 4.2.1 Riser Card Options
- 4.2.2 Removing the PCI Riser Card Assembly
- 4.2.3 Removing an Add-in Card from the Riser Card Assembly
- 4.2.4 Installing an Add-in Card in the Riser Card Assembly
- 4.2.5 Replacing the Riser Card Assembly on the Server Board
- 4.4.1 Installing the GCM Module
- 4.4.2 Installing the RMM Module
- 4.5.1 Installing the LAN Card into the Riser Card Assembly
- 4.5.2 Configuring the RJ45 GbE LAN Card
- 4.5.3 Routing the LAN Card Cables to the Front Panel
- 4.5.4 Connecting the GbE LAN Cables to the Front Panel
- 4.6.1 Preparing the chassis and removing the PCI card carrier assembly
- 4.6.2 Prepare the Fiber LAN Card and install it into the chassis
- 4.6.3 Install the Front Panel Escutcheon and Connect the Fiber Cables
- 4.6.4 Re-assemble the System
- 4.8.1 Installing the RAID Key and RAID DIMM
- 4.8.2 Installing the RAID Intelligent Battery Backup Unit (IBBU)
- 4.9.1 Removing the Optical Device Filler Panel from the Chassis
- 4.9.2 Installing a New Optical Device
- 5 Server Component Replacements
- 5.1.1 Tools and Supplies Needed
- 5.1.2 System References
- 5.1.3 Cable Routing Reference
- 5.2.1 Removing the CPU Fans
- 5.2.2 Replacing the CPU Fans
- 5.2.3 Removing the PCI Fan Assembly
- 5.2.4 Replacing the PCI Fans in the Fan Shroud
- 5.2.5 Installing the Fan Assembly Back into the Chassis
- 5.3.1 Removing the LED Light Pipe Assembly
- 5.3.2 Installing the Front Panel Board Back into the Chassis
- 5.4.1 Removing the Drive Bay Assembly
- 5.4.2 Removing the SAS Backplane Board from the Drive Bay Assembly
- 5.4.3 Installing a New SAS Backplane Board
- 5.4.4 Installing the Drive Bay Assembly
- 5.5.1 Removing the Power Distribution Board
- 5.5.2 Installing the Power Distribution Board Back into the Chassis
- 5.6.1 Removing the Server Board
- 5.6.2 Installing the Server Board Back into the Chassis
- 6 Server Utilities
- 6.1.1 Starting Setup
- 6.1.2 If You Cannot Access Setup
- 6.1.3 Setup Menus
- 6.2.1 Preparing for the Upgrade
- 6.2.2 Updating the BIOS
- 7 Troubleshooting
- 7.2.1 First Steps Checklist
- 7.3.1 Verifying Proper Operation of Key System Lights
- 7.3.2 Confirming the Operating System Load
- 7.4.1 Power Light does not Light
- 7.4.2 No Characters Appear on Screen
- 7.4.3 Characters are Distorted or Incorrect
- 7.4.4 System Cooling Fans do not Rotate Properly
- 7.4.5 Cannot Connect to a Server
- 7.4.6 Diagnostics Pass but the Connection Fails
- 7.4.7 The Controller Stopped Working When an Add-in Adapter was Installed
- 7.4.8 The Add-in Adapter Stopped Working Without Apparent Cause
- 7.4.9 System Boots When Installing a PCI Card
- 7.4.10 Problems with Newly Installed Application Software
- 7.4.11 Problems with Application Software that Ran Correctly Earlier
- 7.4.12 Devices are not Recognized under Device Manager (Windows* OS)
- 7.4.13 Hard Drive(s) are not Recognized
- 7.6.1 BIOS POST Beep Codes
- 8 Warranty
- A.2.1 If AC power supplies are installed:
- A.2.2 If DC power supplies are installed:
- A.2.3 Temperature and Ventilation
- B.1.1 Product Safety Compliance
- B.1.2 Product EMC Compliance - Class A Compliance
- B.1.3 Certifications / Registrations / Declarations
- B.2.1 FCC (USA)
- B.2.2 Industry Canada (ICES-003)
- B.2.3 Europe (CE Declaration of Conformity)
- B.2.4 VCCI (Japan)
- B.2.5 BSMI (Taiwan)
- B.2.6 Regulated Specified Components