Panasonic WJ-MX30 - Manual (Page 10)

49. Color Correction-A Button (A / RESET)
Color correction can be made on the A-bus Source
Video Signal by pressing this button. When you press it
once, the LED starts blinking, the chroma level can be
adjusted by using the Chroma Level Control (47).
When you press it a second time, the LED remains
lighted, and the hue can be adjusted by using the
Position/RGB Control Joystick (46). Chroma level can
also be adjusted by using the Chroma Level Control
(47).
It is also used as Reset Button.
Refer to OPERATION on page 13.
50. Color Correctlon-B Button (B / RESET)
Color correction can be made on the B-bus Source
Video Signal by pressing this button. When you press it
once, the LED starts blinking, the chroma level can be
changed by using the Chroma Level Control (47).
When you press a second time, the LED remains lighted,
the hue can be changed by using the Position/RGB
Control Joystick (46). Chroma level can also be
adjusted by using the Chroma Level Control (47),
It is also used as Reset Button.
Refer to OPERATION on page 13.
• Mix Effect Section
51. Wipe Selection Button (WIPE)
This button is pressed to obtain a wipe effect on the
A-bus Source Video Signal and the B-bus Source Video
Signal depending on the setting of the Wipe Pattern
Select Buttons.
Note :
It is also used as automatic demonstration button.
Press the Power On/Off Button to turn off.
Then press the Power On/Off Button again to
turn on while pressing both of this button and Mix
Select Button (52).
52. Mix Select Button (MIX)
This button is pressed to obtain a mix effect on the
A-bus Source Video Signal and the B-bus Source Video
Signal.
56. B-bus Buttons (B)
These buttons are used to select the desired
audio/video signals allocated to the B-bus input. The
Source 1 /2 corresponds to the Source 1 /2 audio/video
inputs on the rear panel of the instrument.
By pressing the Source 1 and 2 buttons on the B-bus
simultaneously, the External Camera Signals can be
selected.
57. MIx/WipeLED
When the A-bus (B-bus) LED remains lighted and the
Wipe / Mix LED blinks, the Wipe / Mix effect is only
partially produced on the A-bus (or B-bus) side.
58. Mix/WIpe Lever
In wipe mode, manually moving this lever between the
A-bus and B-bus will increase the relative portion of
each bus signal according to the option selected. In
mix mode, the audio and video are switched together
on the A-bus and B-bus.
59. Audio Follow Button (AUDIO FOLLOW)
By pressing this button, the audio on the A-bus and
B-bus can be changed according to the relative
percentage position of the Mix/Wipe Lever (58).
60. Auto Fade/Take Transition Control (TRANSITION)
This control adjusts the automatic fading/auto-take
interval time from 0 to 510 frames at 2-frame
increments.
61. Auto Take Button (AUTO TAKE)
The auto take effect-Automatic Wipe / Mix-can be
executed by pressing this button. This button lights
during the Auto-take interval.
• Fade Control Section
62. Video Fade Button (VIDEO)
Video program output signal fade-in or fade-out is
available with this button.
Use the Auto Fade Button (65) to select fade-out or
fade-in.
53. Luminance Key Select Button (LUM KEY)
The Luminance Key effect is obtained by pressing this
button and adjusting the Luminance Key Level Control
(54). The B-bus Source Signal must be the key signal.
54. Luminance Key Level Control (LEVEL)
This control is used to adjust the Luminance Key Level.
55. A-bus Buttons (A)
These buttons are used to select the desired
audio/video signals allocated to the A-bus input. The
Source 1 /2 corresponds to the Source 1 /2 audio/video
inputs on the rear panel of the instrument.
By pressing the Source 1 and 2 buttons on the
A-bus simultaneously. External Camera Signals can
be selected.
63. DSK Fade Button (DSK)
Downstream Keyed signal fade-in or fade-out is
available with this button.
Use the Auto Fade Button (65) to select fade-out or
fade-in.
64. Audio Fade Button (AUDIO)
Fade-in or fade-out of the audio recording output is
available with this button.
Use the Auto Fade Button (65) to select fade-out or
fade-in.
Note :
The fade-out or fade-in of Head phone output is
cannot be selected.
8 -