Panasonic PT-AE1000 - Manual (Page 20)

OPTION Menu
eiäijtÄ#^ t#hk4aM<A4ii*»i#*WA»*'Ä^A -^vhiWW' < -* < •- «.^ ^ ^ ««. « « äv t»v « m » «i .* v,
ION Menu
o
o o
, ............... .............,,......
«NU ft@0 return a a.
• See “Navigating through
the MENU” on page 28.
When you press INPUT or the INPUT SELECT button
to change the input method, the guidance is indicated in
the upper right corner of the screen. The following
display methods are available. Press ◄ ► to cycle
through the options.
Options Function
OFF Turn off the guidance.
SIMPLE
Display the input method by text.
The INPUT GUIDE will go out after
5 seconds without any operation.
DETAILED
Display the input method by
graphic.
The INPUT GUIDE will go out after
10 seconds without any operation.
You can change the background colour of the menu.
Press ◄ ► to cycle through the options.
Options Function
TYPE1 Semi transparent black
TYPE2 Solid blue
TYPE3 Semi transparent dark blue
You can change the position where to display the menu.
Press ◄ ► to cycle through the options.
UPPER
CENTRE
UPPER
RIGHT
i.OWER
LETT
CENTRE
I OWER
■■'L-NfRE
Lf)WER
RIGHT
You can choose a BLUE or BLACK screen for when the
projector is idle. Press ◄ ► to select an option.
You can switch the logo on/off that is displayed when
starting up. Press ◄ ► to select an option.
• ON: Active
• OFF: Deactive
When the projector is turned on, the input terminals are
detected and an input signal is selected automatically.
You can switch the system on/off. Press ◄ ► to select
an option.
• ON: Active
• OFF: Deactive
NOTE:
• When no signal is detected, the last used input
method will be selected.
HDMI SIGNAL LEVEL
When an HDMI is selected, you can switch the HDMI
signal level NORMAL or EXPAND to display the image.
Press ◄ ► to select an option.
NOTE;
• HDMI SIGNAL LEVEL is not available with some
equipments.
When installing the projector, select the projection
method according to the projector position. Press ◄ ►
to cycle through the options. See “Projection method"
on page 15.
FRONT/DESK
FRONT/CEILING
REAR/DESK
REAR/CEILING
■ .etting on a desk/floor and
projecting from front
Mounting in the ceiling and
projecting from front
Setting on a desk/floor and
projecting from rear
f^lounting in the ceiling and
projecting from rear
You can me I Hired duration of time and set the
off timer to turn off the POWER of the projector
automatically. 3 minutes before turn-off, the countdown
of minutes will be displayed in the lower right corner.
Press ◄ ► to cycle through the options. See “Switching
off the projector automatically” on page 25.
If you use the projector at high elevations, set the fan
speed to HIGH. Press ◄ ► to select HIGH or LOW.
NOTE:
• At 1 400 m (4593 ft) above sea level, the setting
must be HIGH.
You can adjust the power of the lamp to save on
electricity, prolong the lamp life and reduce the noise.
Options Function
______________________ ,
NORMAL
When higher luminance is
required such as movies
ECO - MODE
When lower luminance is
sufficient such as in a small room
NOTE:
• When no input signal is detected, the function is
disabled.
You can check how long the lamp has been used.
NOTE:
• LAMP RUNTIME is a relevant matter for lamp
replacement timing. See “Care and Replacement”
on page 41.
You can assign the frequently use functions to each
function buttons and access to the functions instantly.
FUNCTION BUTTON
1. Press A ▼ to select the required button to assign.
2. Press ENTER.
3. Press ◄ ► to select the required function to
assign.
4. Press RETURN or MENU to return to the previous
menu, or press repeatedly to return to the
projection.
DISABLED SHUTTER
HDMI2 IN AUTO SETUP
HDMI1 IN VIDEO IN
PC IN S-VIDEO IN
SCART IN COMPONENT IN
SHUTTER function
You can turn off the lamp and stop the projection
temporary for electrical power save. Press any
button except the LIGHT, PROJECTOR or
Learning Remote control buttons to return to the
projection.
NOTE:
• See “Selecting the input signal” on page 21,
“AUTO SETUP” on page 36.
• The function buttons are also used as Learning
Remote control buttons. Press the DEVICE button
to switch the control mode. See “Remote Control
Operate Guide” provided with the projector.
38
-
E nglish E nglish - 39