Panasonic PT-AE1000 - Manual (Page 8)

Setting up
You can adjust the projection size with 2.0 power zoom lens. Calculate and define the throw distance as follows.
X CO X in
L (LW/LT)
SW
SCif-.-t,:!)
CO
L (LW/LT)
Projection size (16 : 9) Throw distance (L)
Diagonal length
(SD)
Screen height (SH) Screen width (SW)
Minimum distance
(LW)
Maximum distance
(LT)
1.01 m (40") 0.50 m (1-7") 0.89 m (2'11”) 1,2 m (3-11") 2.4 m (7-10")
127 m (50") 0,62 m (2’) 1.11 m (3-7") 1.5 m (4'11") 3.0 m (9-10")
1.52 m {60") 0.75 m (2-5") 1.33 m (4-4") 1.8m (5’10") 3.6 m (11'9")
1,77 m (70") 0.87 m (2-10") 1.55 m (5-1") 2.1 m (6-10") 4.2 m 0”3'9")
2.03 m (80") 1.00 m (3-3") 1.77 m (5-9") 2.4 m (7-10") 4.8 m (15-8")
2,28 m (90") 1,12 m (3-8") 1,99 m (6-6") 2.7 m (8-10") 5.4 m (17-8")
2.54 m [100") 1.24 m (4-) 2.21 m (7-3") 3.0 m (9'10") 6.0 m (19'8")
3.05 m (120") 1.49 m (4-10") 2.66 m (8-8") 3.6 m (11-9") 7.2 m (23-7")
3.81 m 050") 1.87 m (6-1") 3.32 m(10'10") 4.8 m (15’8") 9.0 m (29'6")
5.08 m
* AH
^200") 2.49 m (8-2") 4.43 m (14-6") 6.0 m (19-8") 12.0 m (39-4")
I Calculation methods for screen dimensions
You can calculate more detailed screen dimensions from the screen diagonal.
SW = SD X 0.872 SH = SD X 0.490
LW= 1,189 x S D - 0 . 0 4 LT = 2,378 x SD - 0.05
Unit: m
The results above are approximate and may differ slightly from the actual measurements.
NOTE;
• Do not use the projector at a raised or a horizontally tilted position as it may
cause malfunction of the projector.
• Make sure the projector lens surface is parallel with the screen. You can tilt
the projector body approximately ± 30° vertically. Overtiiting may result in
shortening the component’s life,
• For the best quality of the projection image, install a screen where sun light or
room light does not shine directly onto the screen. Close window shades or
curtains to block the lights.
You can use the projector with any of the following 4 projection methods. To set the desired method in the projector,
see 'INSTALLATION” on page 39.
Setting on a desk/floor and
projecting from front
P
INSTALLATION: FRONT/DESK
Mounting in the ceiling and
projecting from front
Jll
INSTALLATION: FRONT/CEILING
Setting on a desk/floor and
projecting from rear
R
A
INSTALLATION: REAR/DESK
Mounting in the ceiling and
projecting from rear
r-
INSTALLATION. REAR/CEILING
....
NOTE:
• A translucent screen is required for REAR projection.
• When mounting the projector in the ceiling, the optional ceiling mount bracket (ET-PKX100, ET-PKE1000S)
is required.
You can adjust the throwing angle by screwing the front legs up/down.
This adjust the angle of the projector. See “Positioning the image" on page 21.
f ■ I
NOTE:
• Heated air comes out of the Air exhaust port. Do not touch the Air exhaust port directly,
• If keystone distortion occurs, see “KEYSTONE” on page 36,
14 - E nglish E nglish -15