18-2. function setting, 18-3. data that can be transmitted, 18-4. operation – Kenwood TS-850S User Manual
Page 54: 18-5. split function setting, 1) data that can be transmitted, 2) operation, 4. cw operation
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
4-18-2. Function setting
Turn both transceivers on with the function setting
(menu number 32) at power on. (Please refer to
Section 4-10-15.)
4-18-3. Data that can be transmitted
Data that can be transmitted includes the following:
VFO frequency, VFO A / B, Filter, Mode (with the
TUNE mode). Selected the meter indication, AlP
ON/OFF, 1MHz ON/OFF, FINE ON/OFF
4-18-4. Operation
■ To write the same data to the quick memory
channels of both transceivers
1. Turn the slave transceiver off with the function
setting (menu number 33) at power on. (Please
refer to Section 4-10-15.)
r r
/ /
n r r
2. Press the CLR key.
3. Set the data, such as the frequency to be stored
in the master transceiver, and press the QUICK
MEMO M.IN key of the master transceiver. The
slave transceiver beeps, and the same data is
written to quick memory channels 1 of both
transceivers.
4. When the QUICK MEMO M.IN key is pressed, the
latest data is written to channel 1. If there is
already data in channel 1, it is moved to channel
2
.
For the quick memory recall method, see Section 4-
11-13.
■ To rewrite the VFO frequency of the slave
transceiver directly
1. Turn the slave transceiver on with the function
setting (menu number 33) at power on. (Please
refer to Section 4-10-15.)
2. Press the CLR key.
3. Set the data, such as the frequency to be stored
in the master transceiver, and press the QUICK
MEMO M.IN key of the master transceiver. The
48
data, such as the VFO frequency, in the slave
transceiver is replaced by the data in the master
transceiver. The same data is also written to quick
memory channel 1 of the master transceiver.
4-18-5. SPLIT Function setting
Turn both transceivers on with the function setting
(menu number 35) at power on. (Please refer to
Section 4-10-15.)
(1)
Data that can be transmitted
Data that can be transmitted includes the following:
VFO frequency. Mode (with the TUNE mode)
(2) Operation
■ To write the data to the quick memory channels
of slave transceiver
1. Turn the slave transceiver off with the function
setting (menu number 33) at power on. (Please
refer to Section 4-10-15.)
2. Press the CLR key.
3. Set the data, such as the frequency to be stored
in the master transceiver, and press the QUICK
MEMO M.IN key of the master transceiver. The
slave transceiver beeps, and the data is written to
quick memory channels 1 of slave transceiver.
The data is also written to quick memory channel
1 of the master transceiver.
4. When the QUICK MEMO M.IN key is pressed, the
latest data is written to channel 1. If there is
already data in channel 1, it is moved to channel
2.
For the quick memory recall method, see Section 4-
11-13.
■ To rewrite the VFO frequency of the slave
transceiver directly
1. Turn the slave transceiver on with the function
setting (menu number 33) at power on. (Please
refer to Section 4-10-15.)
2. Press the CLR key.
3. Set the data, such as the frequency to be stored
in the master transceiver, and press the QUICK
MEMO M.IN key of the master transceiver. The
data, such as the TX VFO frequency, in the slave
transceiver is replaced by the data in the master
transceiver. The data is also written to quick
memory channel 1 of the master transceiver.